Herunterladen Inhalt Inhalt Diese Seite drucken

Replacing The Power Cable; Cleaning, Maintenance And Ordering Of Spare Parts - EINHELL TC-AG 115/750 Originalbetriebsanleitung

Winkelschleifer
Vorschau ausblenden Andere Handbücher für TC-AG 115/750:
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 1
6.5 Grinding Wheels
Never use a grinding or cutting wheel bigger
than the specified diameter.
Before using a grinding or cutting wheel,
check its rated speed.
The maximum speed of the grinding or cut-
ting wheel used must be higher than the idle
speed of the angle grinder.
Use only grinding and cutting wheels that are
approved for a minimum speed of 12000 rpm
and a peripheral speed of 67 m/sec.
Check the direction of rotation when you use
diamond cutting wheels. The directional arrow
on the diamond cutting wheel must point in
the direction in which the tool rotates.
Take special care that the grinding/sanding
wheels are properly stored and transported.
Ensure that the grinding/sanding wheels are
never exposed to shock, jolts or sharp edges (for
example during transport or storage in a toolbox).
This could cause damage (such as cracks) to the
grinding/sanding wheels and place the user in
serious danger.
Warning!
6.6 Operating Modes
6.6.1 Rough grinding
Caution: Use the safety device for san-
ding/grinding (included in items supplied).
For the best rough grinding results, hold the grin-
ding wheel at an angle of between 30° and 40° to
the workpiece surface and guide back and forth
over the workpiece in steady movements.
6.6.2 Cutting
Caution: Use the safety device for abrasi-
ve cutting (available as accessory, see 8.4)
When you use the right-angle grinder for cutting
purposes, avoid tilting it in the cutting plane. The
cutting wheel must have a clean cutting edge.
A diamond cutting wheel is best used to cut hard
stone.
It is prohibited to use the machine on as-
bestos materials!
Never use a cutting wheel for rough grin-
ding.
Anl_TC_AG_115_750_SPK13.indb 17
Anl_TC_AG_115_750_SPK13.indb 17
GB

7. Replacing the power cable

Danger!
If the power cable for this equipment is damaged,
it must be replaced by the manufacturer or its
after-sales service or similarly trained personnel
to avoid danger.
8. Cleaning, maintenance and
ordering of spare parts
Danger!
Always pull out the mains power plug before star-
ting any cleaning work.
8.1 Cleaning
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it with compressed air at low
pressure.
We recommend that you clean the device
immediately each time you have finished
using it.
Clean the equipment regularly with a moist
cloth and some soft soap. Do not use
cleaning agents or solvents; these could at-
tack the plastic parts of the equipment. Ensu-
re that no water can seep into the device. The
ingress of water into an electric tool increases
the risk of an electric shock.
8.2 Carbon brushes
In case of excessive sparking, have the carbon
brushes checked only by a qualifi ed electrician.
Danger! The carbon brushes should not be rep
laced by anyone but a qualifi ed electrician.
8.3 Maintenance
There are no parts inside the equipment which
require additional maintenance.
8.4 Ordering replacement parts:
Please quote the following data when ordering
replacement parts:
Type of machine
Article number of the machine
Identification number of the machine
Replacement part number of the part required
For our latest prices and information please go to
www.Einhell-Service.com
Safety guard for cutting (Art. No.: 44.500.51)
- 17 -
12.10.2020 13:18:05
12.10.2020 13:18:05

Werbung

Inhaltsverzeichnis
loading

Diese Anleitung auch für:

44.309.60

Inhaltsverzeichnis