Technical Speci Cations - PEDROLLO PRESFLO Serie Betriebsanleitung

USER'S MANUAL
ELECTRONIC PUMP CONTROLLER
PRESFLO is a device that
®
starts and stops the pump to
which it is tted, thus replacing
traditional pressure switch /
surge tank systems.
The pump is started when, as
a tap is turned on, the pressure
within the system drops below
the "start-up pressure" (Pm),
and is stopped when the ow

Technical speci cations

- Voltage: ~230 Volt / ~115 Volt
- Frequency: 50-60 Hz
- Current: 10A, max 12A for 3 sec.
- Current: 12A, max 16A for 3 sec.
- Protection grade: IP 65
- Start-up pressure (Pm): 0,8/1,5/2,2 bar
(12/22/32 psi)
- Shut-off ow rate (Qa): 2 litres/min (0,5 gpm)
- Connections: 1" BSP / 1" NPT
- Maximum working pressure: 10 bar (145 psi)
- Bursting pressure: 40 bar (580 psi)
- Weight: 650 g
- Protection against:
- dry running (automatic restart)
- repeated start-ups
- Max room temperature: 40°C
- Max liquid temperature: 55°C
- Type of drive: 1C
- Max manual operations on
push button: 1000
- Max automatic operations
on relay: 100000
- Class 3A PTI
- Pollution degree : 2
- Max rated voltage pulse: 2,5 kV
- 230V 12A for EMC test
- Pressure operating
differential: 10 bar
Operating conditions
A. Compatible/non compat-
ible uids
PRESFLO is suitable for use
®
with clean water and chemical-
ly non-aggressive liquids. If the
uid contains impurities, a lter
should be tted upstream.
B. Environmental conditions
PRESFLO should not be used
®
where there is the risk of an
explosion. The temperature
of the location should range
between 0°C and 40°C, and
the humidity should not exceed
90%.
C. Power supply
Make sure that the variation
rate required is zero or less
than the "shut-off ow rate"
(Qa).
PRESFLO 's electronics protect
®
the pump against unsuitable
operating conditions such as
dry running or repeated start-
ups due to leaks.
Before installing,
the product, check that
the RATINGS correspond
with those required.
50066/115 50066/115
CODE: CODE:
~230 / 50 - 60 ~230 / 50 - 60
V / Hz: V / Hz:
16 A 16 A
I max: I max:
1.5 Bar 1.5 Bar
P start: P start:
SN 15060002 SN 15060002
Losses
0 50 100 150 200 l/min
Working area
Pm
Start-up pressure
Qa
Shut-off ow rate
in the power supply is never
more or less than 10 % of the
RATING value.
Higher values may cause
Safety regulations
Before installing or using
PRESFLO , read this manual
®
carefully and thoroughly.
The pump should be installed
and serviced by quali ed per-
sonnel, responsible for making
the hydraulic and electrical
connections in compliance with
the relevant regulations.
PEDROLLO S.p.A. shall not
be held liable for any damage
relating to, or resulting from, an
improper use of the product,
or for any damage relating to,
or resulting from, servicing or
B B
repairs carried out by unqual-
i ed personnel and/or with
non-OEM spare parts.
The warranty, which is valid
for 24 months from the date
of purchase, will no longer be
applicable should the product
suffer damage as a conse-
quence of the use of non-OEM
spare parts, tampering or
improper use.
When starting the installation,
check the following:
Red =
2,2 bar (32 psi)
Blue = 1,5 bar (22 psi)
0,8 bar (12 psi)
Yellow =
2 l/min (0,5 gpm)
Flow rate
damage to the electronic
components.
PRESFLO can only be used
®
with single-phase pumps.
IT EN ES FR DE
- the power supply is switched
off.
- the power lines can withstand
the maximum current.
- the cable bushings and circuit
board cover have been properly
assembled and secured ( see
Electrical Connections ).
- Power supply network must
be tted with proper protection
device (fuse or magne-
to-thermal relay) upstream of
PRESFLO
®
When servicing the product,
check the following:
- the system is not pressurised
(turn a tap on)
- the power supply is switched
off.
Emergency Stop
When in use, the pump can
be stopped in the event of an
emergency:
press STOP/RESTART.
PRESFLO is put STAND-BY.
®
Never disassemble
water accumulator
Water accumulator
12039908PFO
RU
00-19