Safety Instructions; General Information; Installation Instructions - Interline 57100025 Bedienungsanleitung

SAFETY INSTRUCTIONS

Read through these instructions carefully before you use
the product.
Caution: Failure to comply fully with our instructions for
use, or safety instructions, may cause damage to the unit or
injury to individuals.
»
Please read the instruction manual and the directions
shown there.
»
Do not allow children to handle this equipment.
»
Always turn off your filter system when you are working
with your solar collector.
»
Do not position the equipment too close to the pool
(adequate safe distance).
»
Do not use any petroleum-based lubricants. Petroleum
attacks the product's plastic components.
»
This equipment is not intended for use by anyone
(including children) with restricted physical, sensory or
mental ability, or with limited experience and / or limited
knowledge, unless they are supervised by someone
responsible for their safety, or they receive instruction from
them regarding the use of the equipment.
»
Children must be supervised to ensure they do not play
with the equipment.

1 GENERAL INFORMATION

1.1.1 Conditions for the installation of a solar collector
The solar collector you have purchased is intended for use with
in- ground and above-ground pools, and is easy to install and
handle. The installation instructions are based on the following
conditions:
1) You have a pool which is fully built and filled with water.
2) Your pool has a filter system.
3) You have the required connector hoses to supply the
pool and filter system with water. (Ø 38 mm)
These are the requirements so that the solar collector can force
water through the solar chambers when it is installed and fully
connected to the filter pump.
1.1.2 Use (Diagram 1)
Once the equipment is installed, it is connected between your
filter system and your pool using the two hose connectors. The
connector hose forces the cold water from your filter unit into
the solar chambers of your solar collector. Here it is heated by
the sun's energy and then fed on to the second connector hose
towards the pool.
A = feed from the filter unit to the solar collector
B = feed from the solar collector to the swimming pool inlet nozzles
Water heating depends on the following factors: Flow rate and
level of sunshine.
Solar heating only functions efficiently in sunshine. It can also
remain connected to the pump in poor weather as this only
causes a slight loss of pressure in the pump.
4
1.1.3 Tools and accessories required
These tools are required for assembly, but are not included in
your set:
»
Phillips screwdriver
»
Flat head screwdriver
1.1.4 The ideal location for your solar collector
Your solar collector needs to be in a location with as much
sunlight as possible.
»
Never position the solar collector over the surface of
your pool.
»
Keep it an adequate distance away from your pool
(keep a safe distance).
»
The solar collector is designed to allow maximum
possible penetration of sunlight.
1.1.5 Product care
The solar collector should not be exposed to cold weather. The
solar collector should be stored in an area protected from frost
before the first frost, or at the end of the pool season. All parts
must be rinsed or cleaned with water only. Detergents may
damage the protective cover.
1.1.6 Over wintering
Drain all the water from the solar collector by closing off the
pipes. Store the equipment away for winter in an area protected
from frost. Remove the pool return pipes. Make sure there is
no water left inside the equipment as this can freeze. Water
expands as it freezes and so can damage the solar chambers.
2 TECHNICAL DATA
2.1.1 Technical data:
»
Dimensions: L x W x H 110 x 69 x 14 cm
»
Maximum pressure 1 bar at 20°C
»
Waterflow rate max.10,000 l/h
»
Water content collector 15 l
2.1.2 Heat output
Standard figures for heating your swimming pool*
1 m³ water > 1 day > max. 11.1 °C
14 m³ water > 1 day > max. 0.8 °C
14 m³ water > 5 days > max. 4.0 °C
* Results based on 10 hours of direct sunshine per day and may
vary due to changes in weather. The pool was covered with a
solar cover. Outside temperature approx 20 °C.

3 INSTALLATION INSTRUCTIONS

3.1.1. Assembly instructions
1) Remove the solar collector from the packaging.
(Illustration 2)
2) Unscrew the covers from the inlet and outlet.
(Illustration 3)
3) Put the O ring onto both connector pieces and attach
these firmly to the inlet and outlet. (Illustration 5,6)
EN