Technical Data - Milwaukee HDE 13 RQD Betriebsanleitung

TECHNICAL DATA

Rotary Drill
Production code
Rated input
Output
No-load speed
Speed under load max.
Drilling capacity in steel
Drilling capacity in wood
Drilling capacity in Aluminium
Drill chuck range
Drive shank
Weight according EPTA-Procedure 01/2014
Noise information
Measured values determined according to EN 62841. Typically, the A-weighted noise levels of the tool are:
GB
Sound pressure level (Uncertainty K=3dB(A))
Sound power level (Uncertainty K=3dB(A))
Wear ear protectors!
Vibration information
Vibration total values (triaxial vector sum) determined according to EN 62841
Connect only to a single-phase AC current supply and only to the mains voltage speci ed on the
rating plate. Must only be used from sockets with earth wire.:
Vibration emission value a
Uncertainty K=
WARNING
The vibration emission level given in this information sheet has been measured in accordance with a standardised test given in EN 62841 and may be
used to compare one tool with another. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main applications of the tool. However if the tool is used for di erent applications, with di erent
accessories or poorly maintained, the vibration emission may di er. This may signi cantly increase the exposure level over the total working period.
An estimation of the level of exposure to vibration should also take into account the times when the tool is switched o or when it is running but not
actually doing the job. This may signi cantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the e ects of vibration such as: maintain the tool and the accessories, keep the hands
warm, organisation of work patterns.
WARNING Read all safety warnings, instructions, illustra-
tions and speci cations provided with this power tool. Failure
to follow all instructions listed below may result in electric shock, re
and/or serious injury.
Save all warnings and instructions for future reference.
DRILL SAFETY WARNINGS
1) Safety instructions for all operations
a) Use the auxiliary handle(s). Loss of control can cause personal
injury.
b) Hold the power tool by insulated gripping surfaces,
when performing an operation where the cutting accessory
may contact hidden wiring or its own cord. Cutting accessory
contacting a "live" wire may make exposed metal parts of the power
tool "live" and could give the operator an electric shock.
2) Safety instructions when using long drill bits
a) Never operate at higher speed than the maximum speed
rating of the drill bit. At higher speeds, the bit is likely to bend if
allowed to rotate freely without contacting the workpiece, resulting
in personal injury.
English
10
h,D
b) Always start drilling at low speed and with the bit tip in
contact with the workpiece. At higher speeds, the bit is likely to
bend if allowed to rotate freely without contacting the workpiece,
resulting in personal injury.
c) Apply pressure only in direct line with the bit and do not
apply excessive pressure. Bits can bend causing breakage or loss of
control, resulting in personal injury.
Additional Safety and Working Instructions
Use protective equipment. Always wear safety glasses when working
with the machine. The use of protective clothing is recommended,
such as dust mask, protective gloves, sturdy non-slip footwear, helmet
and ear defenders.
The dust produced when using this tool may be harmful to health. Do
not inhale the dust. Use a dust absorption system and wear a suitable
dust protection mask. Remove deposited dust thoroughly, e.g. with a
vacuum cleaner.
Do not machine any materials that present a danger to health (e.g.
asbestos).
Keep mains lead clear from working range of the machine. Always lead
the cable away behind you.
When working in walls ceiling, or oor, take care to avoid electric
cables and gas or waterpipes.
HDE 13 RQD
3844 94 05...
... 000001-999999
825 W
410 W
0-500 min
-1
2,6 min
-1
13 mm
38 mm
20 mm
1,5 - 13 mm
1/2" x 20
3,2 kg
86 dB (A)
97 dB (A)
1,0 m/s
2
1,5 m/s
2