SSS Siedle 130 Produktinformation Seite 6

English
Application
Bus built-in camera 130/180 with
automatic day/night switchover (True
Day/Night) and integrated infrared
lighting. For installation in the cus­
tomer's intercom compartments,
door constructions, letterboxes, etc.
Electrical voltage
Mounting, installation and servicing
work on electrical devices may only
be performed by a suitably qualified
electrician.
1 In the case of video systems, the
following mounting situation must
be avoided at all costs:
• direct backlight
• direct sunlight
• very bright image backgrounds
• highly reflective walls opposite the
camera
• lamps or direct light sources
Scope of supply BCE 053-...
• BCE 053-...
• Terminal block
• This product information
Scope of supply BCE 058-...
• BCE 058-...
• Terminal block
• This product information
Mounting
2 Recommended mounting height
appr. 1.60 m to centre camera.
3 Note the mounting position of the
camera, the type designation must
be legible at the top back of the
module.
4 Pick­up angle of the camera with
an angle of aperture of appr. 130°.
5 Pick­up angle of the camera with
an angle of aperture of appr. 175° in
the full screen mode.
6
6 Note the max. plate thickness
of 6 mm, otherwise it will lead to
adverse effects at the edge of the
camera's field of view.
7 Dimensions for securing the
camera. A cut­out with a diameter
of dia. 51 mm must be provided for
the camera.
8 With an angle of aperture of
appr. 175°, the pick­up angle of
the camera can be adjusted to any
mounting situation. Open the flap
on the back of the module with the
aid of a screwdriver.
9 Set the required picture excerpt
from the camera view (1 to 9) or full
screen (0) using the rotary switch.
Once the required picture excerpt
has been set, close the flap and
mount the module.
10 Select the picture excerpt based
on the existing mounting situation.
The camera's pick­up angle is thus
reduced.
a Picture excerpt (1–3)
top camera alignment
b Picture excerpt (4–6)
central camera alignment
c Picture excerpt (7–9)
bottom camera alignment
Terminal assignment BCE 05x-...
TaK, TbK In­Home bus
camera branch
Ta, Tb In­Home bus
Vc, GND Camera actuation
b, c Power supply 12 V AC
Installation
11 Circuit diagram for BCE 05x­0
a) The TR 603-... (12 V AC, 1.3 A)
can supply the door release and
camera heating.
b) Load, door release/light contact in
line rectifier max. 15 V AC, 30 V DC,
2 A.
c) Door release 12 V AC, use at least
20 Ohm (e.g. TÖ 615-...).
d) Conductor length bus indoor
device – storey call button ERT max.
50 m.
e) When using the video memory
module, the bus telephone
BTCV 850-... must be supplied
by an additional direct voltage
(20–30 V DC, 350 mA).
Dismantling
12 Release the module holder at the
4 fastening points and remove the
module with module holder. There is
no need to disconnect any terminal
block that is already connected,
this can be released by turning to
the left.
13 Unlock the module at the 2
catches and press forward out of the
module carrier. When inserting the
module ensure that it is in the cor­
rect mounting position.
Specifications BCE 053-...
Colour system: PAL
Image pick-up: CMOS sensor 1/3"
756 x 504 Pixel
Resolution: 550 TV lines
Lens: 2.1 mm
2-step heating: 12 V AC
max. 130 mA
Ambient temperature:
–20 °C to +55 °C
Specifications BCE 058-...
Full screen or 9 picture excerpts can
be selected
Electronic image rectification in full
screen
Extended pick-up angle in edge area
for selected picture excerpt
Backlight compensation (BLC)
Colour system: PAL
Image pick-up: CMOS sensor 1/2.7"
1920 x 1080 pixels
Resolution: 600 TV lines
Lens: 1.55 mm
2-step heating: 12 V AC
max. 130 mA
Ambient temperature:
–20 °C to +55 °C