Sharp HT-SB602 Bedienungsanleitung Seite 28

Troubleshooting chart (continued)
Symptom
z Power turns off z Is the HDMI cable connected
suddenly.
z Noise is heard during z Move the speaker away from any
playback.
z When a button is z Set the sound bar to the standby
pressed, the sound
bar does not respond.
z The power is not z Is the sound bar unplugged?
turned on. z The protection circuit may be
z 3D images not z Depending on the TV and Video
displayed on the TV.
z HDMI cable not support 3D image.
z Background noise z Please change to HDMI/ARC or
appears when
connecting with
RCA audio output
terminal connection
from a TV-set/ DVD/
Blu-ray Disc Player.
z Wireless connection z Check the distance between the
cannot be
established.
z Make sure there is no other wireless
z Wireless connection z Make sure there is no obstacles
cannot be
established.
z Manually re-link the sound bar and
„ NFC / Bluetooth
Symptom
z No sound is heard. z The unit is too far from the Bluetooth
z The unit is not paired with the
z Bluetooth sound z The unit is too near to a device that
is interrupted or
distorted. z There is an obstacle between the
z NFC-enabled device z Sound bar is not in Bluetooth pairing
cannot connect to
Bluetooth via NFC
tag.
All manuals and user guides at all-guides.com
Possible cause
correctly? Connect the HDMI cable
correctly and then perform the reset
procedure.
computers or mobile phones.
mode and then turn it back on.
activated. Unplug and plug in the
power lead again after 5 minutes
or more.
component, 3D images may not be
displayed.
Check the operation manual of the
respective component.
headphone terminal from TV-Set/
DVD/Blu-ray Disc Player. This effect
may occur depending on TV/DVD/
Blu-ray Disc Player-Brand, model
and age, and it is not the sound bar
problem.
sound bar and subwoofer (less than
10m (32 feet)).
devices near the unit.
(especially metal) blocking between
the sound bar and subwoofer.
subwoofer (refer page 11).
Possible cause
stereo audio source device.
Bluetooth stereo audio source
device.
generates electromagnetic radiation.
unit and the Bluetooth stereo audio
source device.
mode. Perform "NFC connection for
audio playback". (Refer page 14.)
„ Remote control
Symptom
z The remote control
does not operate
properly.
z The sound bar
cannot be turned
on with the remote
control.
„ Condensation
Sudden temperature changes, storage or operation in an ex-
tremely humid environment may cause condensation inside
the cabinet or on the transmitter on the remote control. Con-
densation can cause the sound bar to malfunction. If this hap-
pens, leave the power on until normal playback is possible
(about 1 hour). Wipe off any condensation on the transmitter
with a soft cloth before operating the sound bar.
„ If problem occurs during operation
When this product is subject to strong external interference
(mechanical shock, excessive static electricity, abnormal
supply voltage due to lightning, etc.) or if it is operated in-
correctly, it may malfunction.
If such a problem occurs, do the following:
1. Set the sound bar to the standby mode and turn the
power on again.
2. If the sound bar is not restored in the previous opera-
tion, unplug and plug in the sound bar again, and then
turn the power on.
„ Factory reset, clearing all memory
Make sure to disconnect all output and input cables at-
tached to the sound bar before performing the factory reset.
1. Press the ON/STANDBY button to enter the power
standby mode.
2. Whilst pressing the SOUND MODE button, press and
hold the ON/STANDBY button until "RESET" appears.
Caution:
This operation will erase all data stored in memory.
E-17
Possible cause
z Is the battery polarity correct?
z Is the battery dead?
z Is the distance or angle incorrect?
z Are there any obstructions in front
of the sound bar?
z Is there a strong light shining on
the remote sensor?
z Is the remote control for another
equipment used simultaneously?
z Is the AC power lead of the sound
bar plugged in?
z Is the battery inserted?