Device Operation - Sthor 82970 Originalanleitung

If unmodifi ed, the plug matches the socket thus reducing the risk of
an electric shock.
After each application, unplug the power cord plug from the socket.
The appliance is intended for indoor use only. Do not expose the ap-
pliance to any precipitation or moisture. If water and moisture enters
the appliance, the risk of an electric shock is signifi cantly increased.
Do not immerse the product in water or any other liquid.
Do not obstruct the ventilation openings and make sure they are
clear. Obstructed and/or clogged ventilation openings may cause
the appliance to overheat. This can lead to damage to the appliance
or cause fi re or electric shock.
Do not overload the power cord. Do not use the power cord to carry,
connect, or disconnect the plug from the power socket. Avoid any
contact between the power cord and heat sources, oil, sharp edges,
and moving parts. Damage to the power cord increases the risk of
an electric shock. If the power cord is damaged (e.g. it is cut or
its insulation is melted), immediately unplug it from the wall sock-
et and return it to an authorised service facility. It is not allowed to
use the product with a damaged power cord. It is not allowed to
have the power cord repaired. It must be changed for a new one
at an authorized service centre. When using extension cords, use
extension cords with power parameters such as those shown on the
appliance's nameplate.
If you notice any damage to any part of the appliance, you must
discontinue using it. In this case, the appliance must be taken to an
authorised service centre or replaced by yourself, if this is permitted
by the user's manual.
Turn off the appliance and unplug the power cord from the wall sock-
et before you start any work on replacing, cleaning, or adjusting.
Switch off the appliance before replacing the accessories and un-
plug the power cord from the socket.
This appliance may be used by children of at least 8 years of age
and by persons with reduced physical, mental abilities and persons
with no experience or knowledge of the appliance, if supervised or
instructed on its safe use so that the risks associated with it were
understandable. Children should not play with the appliance. Unat-
tended children should not be allowed to perform the cleaning and
maintenance of the device.
The vacuum cleaner is designed for dry running. It is forbidden to
draw in water, wet ash or other wet waste. This may result in electric
shock, which may endanger the health and life of the user and others.
Never draw in hot, glowing or burning objects. This can lead to fi re
or explosion and expose the user to serious injury or death. The
maximum temperature of suctioned waste must not exceed 40 ° C.
The device is intended for use in closed rooms and should not be
exposed to water, including precipitation.
Make sure that the mains power parameters comply with the ones
shown on the appliance's nameplate before connecting the power
cord plug to the unit.
Before each use, check the condition of the appliance, including the
O R I G I N A L
10
GB
power cord and plug. If any faults are noticed, do not use the device.
Damaged cables and wires must be replaced with new ones in a
specialist workshop.
Make sure that the power cord plug has been disconnected from the
mains socket before carrying out maintenance on the unit.
Keep the device out of reach of unauthorized persons, especially
children. Make sure that the device is out of the reach of unauthor-
ized persons, especially children also during operation.
Move the device using the handle, do not move the device by pulling
the power cord.
Check the condition of the fl exible hose at regular intervals. Never
use the vacuum cleaner if its fl exible hose is damaged.

DEVICE OPERATION

CAUTION! During all accessories assembly and disassembly activ-
ities, make sure that the power switch is in the "off " position, and in
case of power cord supplied appliance, disconnect the power cord
plug from the socket.
Appliance assembly and disassembly
Take the vacuum cleaner, the dust container, and accessories out
of the packaging and remove all packaging components. Assemble
the dust container.
Before fi rst use, make sure that the vacuum cleaner has all compo-
nents and is correctly assembled.
If the container is mounted on a vacuum cleaner, it must be re-
moved. Slide the lock lever with your fi nger and then remove the
container from the vacuum cleaner (II). Press and hold the lid lock,
then open the dust container lid (II). That way, you can empty the
container without removing the fi lters.
Remove the internal fi lter from the container and then the external fi l-
ter (III). The external fi lter must be positioned inside the dust contain-
er so that the opening on the container side wall is opposite the fi lter
part without perforation (IV). Install the fi lters in the dust container,
close the container lid, and install the container in the vacuum clean-
er. A correctly assembled container cannot be removed otherwise
than by pulling back the lock lever.
Assembly of accessories
Insert the turbo brush (V) into the opening in the vacuum cleaner
housing underneath the dust container. If you need to assemble oth-
er accessories, insert the adapter into the opening and then attach
the selected accessory (VI) to the adapter.
Intended use of the accessories
Turbo brush - a universal brush for cleaning of larger fl at surfaces.
Oval brush - a universal brush with long bristles for cleaning fl at
surfaces, ventilation openings, lockers, and other inaccessible areas
for the turbo brush.
I N S T R U C T I O N S