Masport Maestro Benutzerhandbuch Seite 37

IMPORTANT
The regulator supplied with this BBQ may incorporate
an Excess Flow Control Safety Device. The Excess
Flow Control will activate to prevent gas flow should
a regulator malfunction occur. It is important that the
BBQ operator understands that all gas valves on the
BBQ are closed in the OFF position prior to opening
the gas cylinder valve. If the BBQ valves are open prior
to opening the cylinder valve, the Excess Flow Control
will be activated and prevent the BBQ from being lit.
To reset, close the BBQ valves and gas cylinder valve,
wait for 1 minute and use correct lighting procedure as
detailed below.
LIGHTING THE BBQ
Lighting the BBQ is easy, but must be done with due care.
Make sure that the gas is turned on at the cylinder, or that gas is
available to the BBQ. Also, if your BBQ has a roasting hood, ensure
that the hood is up.
SPARK IGNITION
Push the knob control in and turn anticlockwise to the high position.
You should hear clicking as the igniter creates sparks to light the
gas. Once lit, release the igniter button.
DIFFICULTY LIGHTING
If the burner doesn't light first go, check the gas controls and
try a couple more times. If the burner still does not light, wait a
few minutes to allow the gas to disperse before trying again. If
satisfactory operation cannot be achieved, consult your retailer
before proceeding.
Note: Failure to follow the lighting procedures correctly can lead to
a hazardous condition.
MAIN BURNER AND SIDE BURNER LIGHTING (INTEGRATED
IGNITION)
1. Open the lid before igniting the barbecue
2. Check all the knobs are in the "OFF" position
3. Open the gas control valve at the gas cylinder
NOTE: The valves fitted to this BBQ include a safety
feature. The valve must be depressed before turning. This
feature prevents accidental activation of the knob
4. From the "OFF" position, push in and then turn control knob
anti-clockwise to the "High ( )" position until hearing a "click"
sound.
5. Repeat step 4, 3-4 times until the burner is lit.
6. If the burner fails to light, turn off and wait for 5 minutes, then
begin from step 4
7. Once a burner is lit, similarly light the remaining burners.
8. Turn the knob anticlockwise to adjust the heat from "High ( )" –
"Medium" – "Low ( )" to your heat requirement.
FOR MANUAL LIGHTING (MAIN BURNER)
IMPORTANT
Use a match holder and long match stick or BBQ lighter
for lighting the BBQ manually to avoid burning your hand.
1. Open the lid before igniting the barbecue.
2. Check all the knobs are in the "OFF" position.
3. Open the gas control valve at the gas cylinder.
4. From the "OFF" position, push in and then turn the control
546006.A.1 (GER) - June 2018
knob anticlockwise to the "High ( )" position.
5. Hold a lit match (in a match holder) next to one of the main
burners. The burner will light from the match.
Once a burner is lit, the burner next to it can be turned on and will
light off the lit burner. Repeat until all burners are alight.
Each burner can be adjusted. Turn the knob anticlockwise to
adjust the heat from "High ( )" - "Medium" - "Low ( )" to your heat
requirement.
FOR MANUAL LIGHTING (SIDE BURNER)
1. Turn all knobs to "OFF" position then open the LP tank valve.
Always keep your face and body as far from the grill as
possible when lighting.
2. Raise side burner lid.
3. Push in and then turn control knob anticlockwise to high
position.
4. Use a match holder and long match stick or BBQ lighter for
lighting the BBQ manually to avoid burning your hand. Place a
lit match near the burner until the burner ignites.
5. If burner fails to light, turn off and wait 5 minutes, then try
again. If burner still does not light after repeated attempts, call
your local dealer for assistance.
REAR BURNER LIGHTING
1. Open the lid before igniting the barbecue.
2. Check all the knobs are in the "OFF" position.
3. Open the gas control valve at the gas cylinder.
4. Operate the rear burner knob in combination with the electronic
ignition push button on the side burner table.
5. From the "OFF" position, push in then turn control knob anti-
clockwise to the "High ( )" position.
6. Keep the knob pushed in at the "High ( )" position for 4
seconds whilst pressing the electronic ignition push button.
7. Repeat the steps from beginning, 3-4 times until the burner is
lit.
8. Once the rear burner has ignited keep the knob pushed in at
the "High ( )" position for 20 seconds until stabilized then
release the rear burner control knob.
9. If the burner fails to light, turn off and wait for 5 minutes, then
repeat the steps from beginning.
10. Turn the knob anticlockwise to adjust the heat from High ( )" –
"Medium" – "Low ( )" to your heat requirement.
FOR MANUAL LIGHTING (REAR BURNER)
1. Open the lid before igniting the barbecue.
2. Check all the knobs are in the "OFF" position.
3. Open the gas control valve at the gas cylinder.
4. From the "OFF" position, push in and then turn the rear burner
control knob anticlockwise to the High ( )" position.
5. Hold a lit match (in a match holder) next to rear burner. The
burner will light from the match.
FOR REAR BURNER: LP gas takes longer time to travel from
the valve to the rear burner. Keep the knob pushed in at the
High ( )" position for a further 20 seconds until stabilized, then
release the rear burner control knob. Repeat from step 4, 3-4
times until the burner is lit.
6. If the burner fails to light, turn off and wait 5 minutes, then
begin from step 4.
IMPORTANT
When the rear burner is lit for the first time, both the
rear burner and the gas pipe going from the valve to
the burner (from the front to the rear of the BBQ) needs
to be charged with gas for a successful ignition. Push
the Rear Burner knob in and slowly turn anti-clockwise
and note when ignition (click) sound is heard. Repeat
the action but stop turning just prior to the ignition click,
keeping the knob depressed (in) for approximately 10
seconds to allow the gas to flow to the rear burner, then
complete the turn to ignite the gas. Lighting the rear
burner may not occur in the first instance, repeat if the
first ignition fails.
37