VOLTCRAFT 10 27 33 Bedienungsanleitung Seite 2

OPERATING INSTRUCTIONS
SIDEVIEW ENDOSCOPE CAMERA
ITEM NO.: 10 27 33 1 m / 5.5 mm
ITEM NO.: 10 27 34 2 m / 5.5 mm
ITEM NO.: 10 27 35 3 m / 5.5 mm
INTENDED USE
This product serves as a camera attachment for endoscopes BS-500 and BS-1000T (both
not included in delivery) for visual fault tracing or inspection with dead-voltage systems and
equipment. The flexible camera neck allows the camera at the top to be positioned so it can
reach into otherwise inaccessible locations. The four LEDs built into the camera head enable
shooting in total darkness, with brightness controlled via the connected endoscope. The
waterproof camera neck and camera head are ideally suited for dead-voltage fluids (no acids
or alkaline solutions). Use on humans or animals, or in explosive areas, is not permitted. Power
is supplied via the connected endoscope.
For safety and approval purposes (CE), you must not rebuild and/or modify this product. If you
use the product for purposes other than those described above, the product may be damaged.
In addition, improper use can cause hazards such as short circuiting, fire, electric shock etc.
Read the instructions carefully and keep them. Make this product available to third parties only
together with its operating instructions.
This product complies with the statutory national and European requirements. All company
names and product names are trademarks of their respective owners. All rights reserved.
DELIVERY CONTENT
• Endoscope camera
• Protective cap
• Operating instructions
SAFETY INSTRUCTIONS
Read the operating instructions carefully and especially observe the safety
information. If you do not follow the safety instructions and information
on proper handling in this manual, we assume no liability for any resulting
personal injury or damage to property. Such cases will invalidate the warranty/
guarantee.
a) Persons / Product
• The device is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. These may become
dangerous playing material for children.
• Protect the product from extreme temperatures, direct sunlight, strong jolts, high
humidity, moisture, flammable gases, vapours and solvents.
• Do not place the product under any mechanical stress.
• If it is no longer possible to operate the product safely, take it out of operation and
protect it from any accidental use. Safe operation can no longer be guaranteed if
the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions or
- has been subjected to any serious transport-related stresses.
• Please handle the product carefully. Jolts, impacts or a fall even from a low height
can damage the product.
• Also observe the safety and operating instructions of any other devices which are
connected to the product.
• Observe the statutory regulations relating to the use of the product. Do not use the
product for the surveillance of people, buildings and vehicles!
b) Miscellaneous
• Consult an expert when in doubt about operation, safety or connection of the
device.
• Maintenance, modifications and repairs are to be performed exclusively by an
expert or at a qualified shop.
If you are not sure about the correct connection or use, or if questions arise which are not
covered by these operating instructions, please do not hesitate to contact our technical support
or another qualified specialist.
Voltcraft®, Lindenweg 15, D-92242 Hirschau, Tel. +49 180/586 582 7.
OPERATION
Only immerse the camera head and camera neck in liquids that are voltage
free! The camera neck is not to be submerged further than the marking "MAX
Water Level".
The endoscope may only be used for inspection of dead systems. The camera
head is made of metal and can lead to short circuits. For safety reasons,
disconnect all system parts from the power supply before every inspection.
Avoid strong mechanical strains or vibrations. Make sure you never go below
VERSION 06/12
the minimum bending radius of 50 mm.
Put the protective cap back onto the camera lens when the camera is no longer
in use.
1. Plug the connecting plug on the top of the endscope carefully into the connecting socket of
the camera neck.
Make sure that the connecting socket is oriented exactly towards the pins of the
connecting plug. There is an arrow printed on the connecting socket. This arrow must
point towards the display of the endoscope.
2. Turn the mounting ring clockwise to fasten the connection.
You will find notes on controlling the brightness of the LEDs in the operating instructions
of the manual.
3. Follow these steps in reverse order when disconnecting the camera from the endoscope.
CLEANING
• To clean the camera lens, use a small brush or cotton swab.
• To clean the camera neck, use a cloth lightly dampened with lukewarm water.
DISPOSAL
Electronic devices are recyclable waste and must not be disposed of in the household
waste.
At the end of its service life, dispose of the product according to the relevant statutory
regulations.
TECHNICAL DATA
Image sensor .....................................320 x 240 CMOS
Camera lighting .................................4 white LEDs, 1000 lux/20 mm
Exposure ...........................................automatic
White balance ....................................fixed
Operating / storage temperature .......-20 to +60 ºC
Operating / storage humidity .............max. 95 %
Min. bend radius ................................50 mm
Protection class .................................IP67
Field of view .......................................54º
Depth of field .....................................15 – 50 mm
ø ........................................................5.5 mm
Length................................................1 m (item no.: 10 27 33), 2 m (item no.: 10 27 34)
Weight ...............................................120 g
Legal notice
These operating instructions are a publication by Voltcraft®, Lindenweg 15, D-92242 Hirschau/Germany, Phone +49 180/586 582 7
(www.voltcraft.de).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data processing
systems require the prior written approval by the editor. Reprinting, also in part, is prohibited.
These operating instructions represent the technical status at the time of printing. Changes in technology and equipment reserved.
© Copyright 2012 by Voltcraft®
3 m (item no.: 10 27 35)