Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
log file and is stored on the SD-C
high-quality SD-Cards with sufficie
• Adjustment control: monitored by
audio signal.
• Battery detection: when connecti
automatic recognition of cell coun
number of the tones is equal to th
recognised Cells.
long signal tone:
short signal tone:
As for example:
1 short + 1 long tone:
2 long + 2 short tones:
• Very sensitive control character
start-up.
• Sensing and computing of the
data: self adjusting clock frequenc
higher), dynamic timing
• Start protection at power up, bl
protection, over temperature pro
current limitation.
• Digital microprocessor control:
thermal drift.
• Updatable: online firmware update
• Please note, that the JIVE Pro
PROGCARD compatible.
• 24 months warranty:for items with
purchase.
• CE tested
• Fast repair service: in-house servi
• Free of charge Hotline (when
Germany): during our daily busines
For
information
www.kontronik.com (Service-Cente
• Developed and produced in Rotten
Germany.
4.2 Cooling and mounting
Sufficient cooling increases the ef
lifespan of the ESC. When mounting
the model, make sure to mount
cooling plate facing upward. If using
should be placed fins up, and unco
installing the heatsink, for the b
between the cooling components,
recommends attaching the heatsink w
paste. For more cooling,you may att
screwing it onto the heat sink and
directly into the JIVE Pro.
www.modellmarkt24.ch
www.modellmarkt24.ch
16
Card (use only
ient speed).
y LED and / or
cting a battery,
unt begins. The
the number of
4 Cells re
ecognised
1 Cell rec
ecognised
5 Cells
lls
10 Cells
lls
ristic: smooth
actual motor
cy (32 kHz or
locked motor
otection, over
therefore no
ate possible.
ESC is not
ith EU proof of
rvice centre.
n calling from
ess hours.
to
business
hours
er)
nburg,
efficiency and
ing the ESC to
nt it with the
g a heatsink, it
covered. When
best transfer
KONTRONIK
with a thermal
attach a fan by
nd plugging it
4.3 BEC
The JIVE Pro ESC
Compared to general B
of the BEC is designed
input voltage. This allows
higher voltages. In additi
a high interference reject
BEC capacity of JIVE Pro
8 A continuous
20 A max peak cu
BEC Voltage (default 5.6
The BEC-voltage can be
(in 0.1 V steps) by using
For
safety
connecting either a
!
(adjusted BEC voltage
LiPo battery (adjuste
4-cell NiCd battery (a
V) in parallel to the rec
ATTENTION: please
!
receiver are compat
voltage
Operation without BEC:
When operating withou
cable is to be disconnect
4.4 Torodial core
The factory mounted toro
cable allows suppressio
not be removed from
reasons, but it can b
anywhere within the cab
Never remove the torodial core fr
Itcan be moved within the cable
take care for tight fit of the cable
see:
4.5 Active freewheeling
To optimize the efficienc
and to reduce heating o
features an active freew
freewheeling circuit sho
low throttle settings
discontinuity of motor RP
4.6 Part load capability
Due to its active freew
may be operated in par
do not exceed the JIVE
has a switched BEC.
BEC-systems the capacity
d to be independent of the
ws the usage of the BEC at
ition, the JIVE Pro features
tion.
Pro
urrent
.6 V)
be adjusted from 5 V to 8 V
g the programming unit.
reaso
sons,
we
recommend
a 2-cell LiFePo battery
ge: 6,6 V – 7 V) or a 2-cell
ed BEC voltage: 8 V) or a
adjusted BEC voltage: 5,6
eceiver.
e ensure the servos and
atible with the requested
ut BEC, the red receiver
cted or removed.
orodial core on the receiver
ion of interference. It must
m the cable for security
be moved, if necessary,
ble.
from the cable!
le to any position, but
.
lesafterwards
ng circuit
ncy of partial load operation
of the ESC, the JIVE Pro
wheeling circuit. The active
hould not be used at very
as this may result in
PM.
ty
wheeling circuit, the ESC
artial load conditions if you
E Pro's continuous current
Werbung
Kapitel
Inhaltsverzeichnis
