Noise Information; Vibration Informa- Tion; Installation - Kress KUX35P Bedienungsanleitung

NOISE INFORMATION

A weighted sound pressure
A weighted sound power
K & K
PA WA
Wear ear protection.
VIBRATION INFORMA-
TION
Vibration total values (triax vector sum) determined
according to EN 60745:
Vibration emission value a
17.918m/s
Chiseling
Uncertainty K= 1.5m/s²
The declared vibration total value may be used for
comparing one tool with another, and may also be used
in a preliminary assessment of exposure.
WARNING: The vibration emission value during
actual use of the power tool can differ from the
declared value depending on the ways in which the tool
is used dependant on the following examples and other
variations on how the tool is used:
How the tool is used and the materials being cut or
drilled.
The tool being in good condition and well maintained
The use the correct accessory for the tool and ensuring
it is sharp and in good condition.
The tightness of the grip on the handles and if any anti
vibration accessories are used.
And the tool is being used as intended by its design
and these instructions.
This tool may cause hand-arm vibration
syndrome if its use is not adequately managed
WARNING: To be accurate, an estimation of
exposure level in the actual conditions of use
should also take account of all parts of the operating
cycle such as the times when the tool is switched off
and when it is running idle but not actually doing the
job. This may significantly reduce the exposure level
over the total working period.
Helping to minimise your vibration exposure risk.
ALWAYS use sharp chisels, drills and blades
Maintain this tool in accordance with these instructions
and keep well lubricated (where appropriate)
If the tool is to be used regularly then invest in anti
vibration accessories.
Plan your work schedule to spread any high vibration
tool use across a number of days.
L =87.9dB(A)
pA
L =101.9dB(A)
wA
3dB(A) & 2.4dB(A)
=
h,Cheq
2
OPERATION
INSTRUCTIONS
NOTE: Please read the instructions carefully
before use.
INTENDED USE
This machine is suitable for gouging on concrete,
bricks, stone and asphalt. After appropriate
accessories are installed, it can also be used for
squeezing and tamping.

INSTALLATION

Warning: Be sure to unplug the power
cord before any commissioning or repair
on the machine.
1. AUXILIARY HANDLE (SEE FIGURE A)
You can change the position of the auxiliary handle (8)
as needed to improve work safety and comfort.
Tighten the auxiliary handle (8) in the counter-clockwise
direction and loosen the auxiliary handle (8)in the
clockwise direction.
Warning: The auxiliary handle must be
used during operation.
2. CHISEL
With the chucks (2), the chisel can be easily replaced
without other auxiliary tools.
The dust-proof cover (1) prevents the dusts from
entering the chisel during operation. Be cautious when
installing a chisel without damaging the dust-proof
cover (1).
Warning: Replace the dust-proof cover
once it is damaged. To avoid danger, it
must be replaced by the special service center,
or an professional person with equivalent
qualifications.
1) INSTALLATION
Pull down the chuck (2) and screw it into the chisel.
Release the chuck (2) to lock the chisel. (See Figure
B1-B3)
Pull the chisel to make sure it is locked.
2) DISASSEMBLY
Pull down the chuck (2) and remove the chisel. (See
Figure C)
NOTE: Use a sharp chisel to achieve good
performance. It is important to grind the chisel in
time to extend its service life and achieve better
performance.
3) Regularly add lubricant to the gearbox
Open the oil cover (3) with the accompanying wrench,
and add the appropriate amount of grease (see Figure
D)
3. CHISEL POSITION ADJUSTMENT
After attaching chisel, push chisel adjustment ring (9)
toward the chuck (2) and rotate. Adjusting chisel's
angle to make it at the proper position, then release the
chisel adjustment ring and make sure chisel clips into
the slot firmly. (See Figure E1, E2, E3)
ATTENTION: Do not adjust chisel when the tool is on
operation
7
EN