Herunterladen Inhalt Inhalt Diese Seite drucken

Operation - EINHELL PICOBELLA Originalbetriebsanleitung

Akku-oberflächenbürste
Vorschau ausblenden Andere Handbücher für PICOBELLA:
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen

Verfügbare Sprachen

Important!
Observe the requirements of EN 1717 in rela-
tion to the connection of the water connection
to the drinking water network. Consult a spe-
cialist plumbing company.
Never direct the water jet at electric cables or
the equipment itself.
The water temperature must be between
+5°C and +35°C.
Do not use water that is dirty, gritty or con-
tains any chemical products, as these could
impair operation and shorten the life of the
equipment.
The connection to the water inlet must be fi tted
with a connector for standard hose coupling sys-
tems (Fig. 7 / Item 11). Pass a water hose (approx.
Ø 13 mm (½")), through the additional handle as
shown in Fig. 12 and attach the hose coupling to
the connection for the water inlet (Fig. 13). Re-
move the hose clip (Fig. 2 / Item 7) from the long
handle and secure the hose to the long handle
with the hose clip (Fig. 14a/14b).
Each time before use, check the following:
That the equipment is in perfect condition and
that the safety devices and the cleaning brush
are complete.
That all screws are securely fastened.
That all moving parts move smoothly.
5.8 Fitting the battery (Fig. 15)
Push the battery into the battery mount provided.
The battery will be heard to click into place when
it has been pushed fully in. To take out the battery,
press the pushlock button (Item H) and remove
the battery.
5.9 Charging the battery (Fig. 16)
1. Take the battery pack out of the equipment.
Do this by pressing the pushlock button.
2. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Insert the power plug of the charger
into the socket outlet. The green LED will then
begin to fl ash.
3. Insert the battery pack into the charger.
4. In the section entitled „Charger indicator" you
will fi nd a table with an explanation of the LED
indicator on the charger.
The battery pack can become a little warm during
the charging. This is normal.
If the battery pack fails to charge, check:
whether there is voltage at the socket outlet
Anl_Picobella_SPK7.indb 25
Anl_Picobella_SPK7.indb 25
GB
whether there is good contact at the charging
contacts
If the battery pack still fails to charge, send
the charger
and the battery pack
to our customer service center.
To ensure that the battery pack provides long ser-
vice, you should take care to recharge it promptly.
You must recharge the battery pack when you
notice that the power of the cordless equipment
drops. Never allow the battery pack to become
fully discharged. This will cause it to develop a
defect.
5.10 Battery charge level indicator (Fig. 17)
Press the button for the battery charge level indi-
cator (Item K). The battery charge level indicator
(Item L) shows the charge status of the battery
using 3 LEDs.
All 3 LEDs are lit:
The battery is fully charged.
2 or 1 LED(s) are lit:
The battery has an adequate remaining charge.
1 LED blinks:
The battery is empty, recharge the battery.
All LEDs fl ash:
The battery pack has undergone exhaustive di-
scharge and is defective. Do not use or charge a
defective battery pack.

6. Operation

Please note that the statutory regulations gover-
ning noise abatement may diff er from one loca-
tion to another.
Danger! The brush covers on the side must be
fi tted when carrying out work.
Warning!
Make sure that you have fitted the brush
which is intended to be used for the surface
you want to clean.
Make sure that the brush covers on the side
are fitted securely.
Inspect the brushes to check them for dirt
before you start your cleaning work and clean
- 25 -
19.11.2019 09:17:08
19.11.2019 09:17:08

Werbung

Inhaltsverzeichnis
loading

Diese Anleitung auch für:

34.242.03

Inhaltsverzeichnis