Renkforce RF100 Wichtige Informationen Seite 2

IMPORTANT INFORMATION
RF100 3D printer fully-assembled
Item no. 1507428
Dear Customer,
thank you for purchasing this product.
For safety and approval purposes, you must not rebuild and/or modify this product. If you use
the product for purposes other than 3D printing, the product may be damaged. In addition,
improper use can result in short circuits, fires, electric shocks or other hazards. Read the
important information carefully and store them in a safe place. Make this product available to
third parties only together with the quick-start-guide and this important information.
Detailed Operating Instructions
Download the detailed operating instructions at www.conrad.com/downloads
or scan the QR code shown. Follow the instructions on the website.
General information on the 3D printer
A 3D printer is a highly complex device in which many parameters must be set
depending on the printer, printed object and filament material used.
Additionally, the adhesion of the printed object on the printing plate is
influenced by printing plate temperature, filament material, shape of the
printed object and surface properties of the printing plate.
Ambience influences such as drafts, grease on the printing plate, etc. also
play a role in the quality and adhesion of the printed object.
For the above reasons, it is not possible to reach high-quality print results at
once and without previous experiments.
Change the adjustable parameters in small steps for the best printing results
for your application.
The printing examples enclosed on the SD-card provide references, but must
be refined for perfect results depending on the above parameters.
Safety Information
Read the operating instructions carefully and especially observe the safety
information. If you do not follow the safety instructions and information
on proper handling in the manual, we assume no liability for any resulting
personal injury or damage to property. Such cases will invalidate the warranty/
guarantee.
• For safety reasons, any unauthorized conversions and/or modifications to the
product deviating from these operating instructions are not permitted. Components
may be damaged and thus impair the function or safety of the device.
• When setting up the 3D printer, observe that the mains switch of the device must
be easy to reach so that the device can be switched off quickly and easily in case
of malfunction.
• Never reach into the 3D printer in operation. The mechanically moved parts within
the printer pose a high risk of injury!
• The nozzle grows very hot in operation. Never touch this part during or just after
operation. Let it cool down sufficiently first (approx. 60 minutes).
• All persons who operate this product, mount, install, assemble it, put it into
operation or service it must be trained and qualified accordingly and must observe
these operating instructions.
• Disconnect the device from the mains before maintenance work or modifications
(unplug the mains plug) and let it cool down.
• In operation, there will be noise and, depending on the filament material used,
smells. Observe this when selecting the site of setup and the filament material.
Ensure sufficient ventilation or install an extraction system. Do not inhale arising
vapours. When using any other than the recommended filament material,
poisonous vapours or gases may develop.
• The 3D printer is not suitable for persons with physical, sensor or mental limitations
or for inexperienced or uninformed persons.
• This product is not a toy and not suitable for children. Children cannot judge the
dangers involved when handling electrical devices.
• The only permissible voltage source is a properly grounded mains socket
(100-240 V, 50/60 Hz) of the public mains.
• The devices must not be exposed to any extreme temperatures, strong vibrations,
high moisture, such as rain or steam or strong mechanical strain.
• Never place containers containing liquids, e.g. glasses, vases, etc. on the device
or in its vicinity and do not pour any liquids out over the device. Liquids may get
into the housing and impair electrical safety. This also poses great danger of fire
or potentially fatal electric shock!
If this is the case, first power down the respective mains socket on all poles (e.g.
switch off circuit breaker and FI switch) and then pull the mains cable from the
socket. Disconnect all lines from the device. Do not operate any part of the product
anymore afterwards, but take it to a specialist workshop.
• Never place any sources of open fire, such as lit candles, on or right next to the
device.
• Do not touch the mains cable if it is damaged. Power down the respective mains
socket (e.g. via the circuit breaker) and then carefully unplug the mains plug from
the mains socket. Never use the product if the mains cable is damaged.
• Make sure that the mains cable is not squeezed, bent, damaged by sharp edges
or put under mechanical stress. Avoid excessive thermal stress on the mains
cable from extreme heat or cold. Do not modify the mains cable, otherwise it may
be damaged. Damaged mains cables can cause a fatal electric shock.
• Never touch the mains line or the mains plug with wet or damp hands. There is a
risk of potentially fatal electric shock!
• The mechanical parts of the product are produced highly precisely. Never apply
any mechanical force here. The 3D printer may be rendered useless by this.
• Never operate the device unattended.
• Only operate the device in moderate climates, never in tropical climates.
• Do not leave packaging material lying around carelessly. This may become
dangerous playing material for children.
• Consult an expert when in doubt about the operation, safety or connection of the
appliance.
• Maintenance, modifications and repairs must only be completed by a technician
or an authorised repair centre.
• If you have questions which remain unanswered by these operating instructions,
contact our technical support service or other technical personnel.
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in
electronic data processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited.
This publication represent the technical status at the time of printing.
Copyright 2016 by Conrad Electronic SE. *1507428_V2_1116_02_LS_hs_gb