Whirlpool T1400 Handbuch Seite 17

The installation must be made by a qualified person, carefully observing all the manufacturer's indications. After
having unpacked the dishwasher, inspect it to see if it has been damaged during shipment. If there is any
suspect evidence, consult a service representative. All the packing materials (bags - Styrofoam - nails - etc.)
must not be left where they can cause harm to persons, especially children. When installing, made certain the
unit is perfectly level - adjusting the feet as required as this will ensure correct operation.
When locating the machine, allow plenty of free space around it to permit easy access and operation
by maintenance personnel. Remove the rear panel to permit making the water connections. Mount any
shelves, benches or roller units that are to be mounted to the machine inlets and outlets, and then
make the end-travel micro switch electrical connections at the terminals located inside the machine. The machine
must be fitted with detergent and brightening dosing equipment, which will be furnished and installed by the firm
that supplies the cleaning products. The electrical terminal strip for making connections to the dosing units is
located inside the electrical box.
The terminals (B) and (D) on the terminal strip are for the dosing connections: (B) for the brightener and (D) for the
detergent. Do not pour detergent directly into the tubs; this will cause dark marks to appear on their surfaces. Only
use antifoaming detergent. The brightening equipment (B) operates on 24V, and the detergent equipment (D)
operates on the mains voltage. The machine equipped with a IPX1 degree of protection and should therefore not
be washed using direct jets of water.
4.1 WATER CONNECTIONS:
The machine has a filter whose inlet, install a maintenance and safety valve in an easily accessible position
upstream. The water temperature should be between 50°and 55°C; the pressure should be between 200/400 kPa
and the water hardness should be between 7° and 12° French.
Hold down the button located next to the thermostat and fill the boiler with water. When the boiler is completely full,
water will issue from the rinsing nozzles. Now set the thermostat to 90°C.
Be careful here, because if you let it get to high you could burn out the electrical.
With machines that have a steam-condenser and heat energy-recovery capability, cold water must be feeding at a
temperature of between 10° and 15°C.
4.2 DRAIN WATER:
Install a floor-level discharging siphon connected to the discharge drain. If no siphon is provided, install one soas to
avoid fumes. Make sure that the discharge tube can resist a temperature of 70°C and no kinks in it.
4.3 STEAM FEEDING:
Connect to the machine fittings as shown in the installation drawing. Install quick-closing and shit-off valves to
make the equipment independent from the main line. The steam should be supplied, saturated and dry, at
pressures ranging between a minimum of 0.5 bar (50Kpa-110.8°C) and a maximum of 0.8 bar (80Kpa-110.8°C)
4.4 STEAM DRAIN:
The condensed steam discharge line to the recovery system has to have an adequate slope to provide positive
evacuation. Install a recycling pump if required. This is only for steam heated machine. A maintenance quick
closing valve should be installed in parallel with the condensate discharge, so as to be able to deviate the
condensate to the sewer.
Caution: make sure that the supply and drain tubes are not bent, restricted or crushed after
installation.
4.5 Electrical connection
The dishwasher's electrical connection, and that of eventual supplementary apparatus, is to be entrusted
to authorized and qualified personnel, with respect to the norms in vigor; the technical regulations for the
connections are also to be observed. The total power installed is given upon the apparatus' technical
data label.Other apparatus must not be protected together with the dishwasher.
The user must provide for the installation, according to the norms in vigor, of a main electrical power
switch and of a differential switch compatible with the machine's characteristics.
These switches must be installed near the dishwasher, be easily accessible after installation and
guarantee complete disconnection from the electrical supply in category III over voltage conditions.
Caution!!!
The dishwasher is free of electrical current only when the main switch is off.
Connect the apparatus to the usage equalizer. The
‐
back of the machine.
The protection conductor (PE) is yellow-green in color, the neutral conductor (N) is blue (only on models
‐
5
clamp for the connection is located at the lower