Maintenance - AEG US 1300 XE Originalbetriebsanleitung

TECHNICAL DATA RECIPROCATING SAW
Production code.......................................................................
Rated input ..............................................................................
Output ......................................................................................
Stroke rate under no-load ........................................................
Lengths of stroke .....................................................................
Weight according EPTA-Procedure 01/2014 ...........................
Noise/vibration information
Measured values determined according to EN 62841.
Typically, the A-weighted noise levels of the tool are:
Sound pressure level (Uncertainty K=5 dB(A)).....................
Sound power level (Uncertainty K=5 dB(A)) .........................
Wear ear protectors!
Total vibration values (vector sum in the three axes)
determined according to EN 62841.
Cutting board *
Vibration emission value a .................................................
h,B
Uncertainty K= ......................................................................
Cutting wooden beam *
Vibration emission value a ...............................................
h,WB
Uncertainty K= ......................................................................
* with saw blade HCS, dimension 150 x 19 x 1,2 mm and tooth pitch 4,2 mm
WARNING
The vibration and noise emission level given in this information sheet has been measured in accordance with a standardized
test given in EN 62841 and may be used to compare one tool with another. It may be used for a preliminary assessment of
exposure.
The declared vibration and noise emission level represents the main applications of the tool. However if the tool is used for
diff erent applications, with diff erent accessories or poorly maintained, the vibration and noise emission may diff er. This may
signifi cantly increase the exposure level over the total working period.
An estimation of the level of exposure to vibration and noise should also take into account the times when the tool is switched
off or when it is running but not actually doing the job. This may signifi cantly reduce the exposure level over the total working
period.
Identify additional safety measures to protect the operator from the eff ects of vibration and/or noise such as: maintain the tool
and the accessories, keep the hands warm, organization of work patterns.
WARNING Read all safety warnings, instructions,
illustrations and specifi cations provided with this power
tool. Failure to follow all instructions listed below may result
in electric shock, fi re and/or serious injury.
Save all warnings and instructions for future reference.
SABRE SAW SAFETY WARNINGS
Hold the power tool by insulated gripping surfaces,
when performing an operation where the cutting
accessory may contact hidden wiring.
Cutting accessory contacting a „live" wire may make
exposed metal parts of the power tool „live" and could give
the operator an electric shock.
Use clamps or another practical way to secure and
support the workpiece to a stable platform. Holding the
work by your hand or against the body leaves it unstable
and may lead to loss of control.
Wear ear protectors. Exposure to noise can cause hearing
loss.
ADDITIONAL SAFETY AND WORKING INSTRUCTIONS
Use protective equipment. Always wear safety glasses when
working with the machine. The use of protective clothing is
recommended, such as dust mask, protective gloves, sturdy
non-slip footwear, helmet and ear defenders.
The dust produced when using this tool may be harmful to
health. Do not inhale the dust. Wear a suitable dust
protection mask.
Do not machine any materials that present a danger to
health (e.g. asbestos).
Switch the device off immediately if the insertion tool stalls!
Do not switch the device on again while the insertion tool is
stalled, as doing so could trigger a sudden recoil with a high
12 ENGLISH
US 1300 XE
......................474961 01...
...000001-999999
.......................1300 W
.........................650 W
....................0-2800 min -1
...........................30 mm
..........................3,8 kg
........................92,5 dB (A)
......................103,5 dB (A)
........................18,5 m/s
2
..........................1,5 m/s
2
........................19,5 m/s
2
..........................1,5 m/s 2
reactive force. Determine why the insertion tool stalled and
rectify this, paying heed to the safety instructions.
The possible causes may be:
• it is tilted in the workpiece to be machined
• it has pierced through the material to be machined
• the power tool is overloaded
Do not reach into the machine while it is running.
The insertion tool may become hot during use.
WARNING! Danger of burns
• when changing tools
• when setting the device down
Chips and splinters must not be removed while the machine
is running.
When working in walls ceiling, or fl oor, take care to avoid
electric cables and gas or waterpipes.
Clamp your workpiece with a clamping device. Unclamped
workpieces can cause severe injury and damage.
Do not use cracked or distorted saw blades.
Plunge cuts without pre-drilling a hole are possible with soft
materials (wood, light building materials for walls). Harder
materials (metals) must fi rst be drilled with a hole
corresponding to the size of the saw blade.
Always place the guide shoe on the workpiece when
sawing.
SPECIFIED CONDITIONS OF USE
This sabre saw cuts wood, plastic, and metal. It cuts curves
and can cut fl ush to a surface.
Do not use this product in any other way as stated for
normal use.
EC-DECLARATION OF CONFORMITY
We declare under our sole responsibility that the product
described under "Technical Data" fulfi lls all the relevant
provisions of the directives 2011/65/EU (RoHS), 2014/30/
EU, 2006/42/EC and the following harmonized standards
have been used:
EN 62841-1:2015
EN 62841-2-11:2016
EN 55014-1:2017
EN 55014-2:2015
EN 61000-3-2:2014
EN 61000-3-3:2013
EN IEC 63000:2018
Winnenden, 2019-08-23
Alexander Krug
Managing Director
Authorized to compile the technical fi le.
Techtronic Industries GmbH
Max-Eyth-Straße 10
71364 Winnenden
Germany
MAINS CONNECTION
Connect only to single-phase a.c. current and only to the
system voltage indicated on the rating plate. It is also
possible to connect to sockets without an earthing contact
as the design conforms to safety class II.

MAINTENANCE

If the replacement of the supply cord is necessary, this has
to be done by the manufacturer or his agent in order to
avoid a safety hazard.
The ventilation slots of the machine must be kept clear at all
times.
Use only AEG accessories and AEG spare parts. Should
components need to be replaced which have not been
described, please contact one of our AEG service agents
(see our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered.
Please state the machine type printed as well as the six-digit
No. on the label and order the drawing at your local service
agents or directly at: Techtronic Industries GmbH,
Max-Eyth-Straße 10, 71364 Winnenden, Germany.
SYMBOLS
CAUTION! WARNING! DANGER!
Always disconnect the plug from the socket
before carrying out any work on the machine.
Please read the instructions carefully before
starting the machine.
Wear gloves!
Always wear goggles when using the machine.
Accessory - Not included in standard
equipment, available as an accessory.
Do not dispose of electric tools together with
household waste material.
Electric tools and electronic equipment that
have reached the end of their life must be
collected separately and returned to an
environmentally compatible recycling facility.
Check with your local authority or retailer for
recycling advice and collection point.
Class II tool, tool in which protection against
electric shock does not rely on basic insulation
only, but in which additional safety precautions,
such as double insulation or reinforced
insulation, are provided.
There being no provision for protective earthing
or reliance upon installation conditions.
n
Stroke rate under no-load
0
V Volts
AC Current
European Conformity Mark
Ukraine Conformity Mark
EurAsian Conformity Mark.
ENGLISH 13