Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Learning with double button:
I. In normal operating mode, press buttons # and ＊ together. The remote keypad will generate a long beep.
<
N
O
T
E
>
<
N
O
T
E
>
If the remote keypad does not generate a long beep, it means that no learning data has been set to the
control unit; press button # and * to send the learning data again.
II. The respective information will be shown if the control unit receives the learning data. Refer to the control unit instruction
manual to complete the learning procedure.
III. After having received the remote keypad data, the control unit will send a confirmation to the remote keypad itself. The
remote keypad will beep three times to confirm that validation was received.
<
I
M
P
O
R
T
A
N
T
N
O
T
<
I
M
P
O
R
T
A
N
T
N
O
T
If the remote keypad does not beep three times, run the learning procedure again.
Step 3:
After run the remote keypad learning procedure, set Walk Test mode on the control unit, keep the remote keypad
in the desired position and send the learning data to the control unit to check that it is within the range of the
control unit signal. To send learning data, press button ＊ and then button 7 in Test mode or press buttons # and
＊ in normal operating mode.
Step 4:
Once the correct operation of the remote keypad in the chosen position has been checked, proceed with the
installation following the procedure described below (see Mounting the remote keypad).
Step 5:
Modify the local code to access test mode, if necessary:
I. With the keypad in Test mode, press button ＊ and then button 6: the keypad will generate a long beep.
II. Enter 0000 (default code).
III. Press button
IV. Enter the new 4-digit code.
V. Press button #: the remote keypad will generate a long beep. The new code is enabled.
Step 6:
Press the button twice
M
o
u
n
t
i
n
g
t
h
e
r
e
m
o
M
o
u
n
t
i
n
g
t
h
e
r
e
m
To mount the remote keypad:
I. Remove the front lid.
II. Using the two assembly holes of the rear cover as a template, mark the position of the holes in the more suitable
position.
III. Insert the anchor bolts if the device is fixed to plaster or bricks.
IV. Screw the remote keypad to the anchor bolts.
V. Close the front lid.
H
o
w
t
o
s
e
t
o
p
e
r
a
t
i
H
o
w
t
o
s
e
t
o
p
e
r
a
t
Arming can be enabled with or without entering the user code.
Arming with user code (default setting = 1234)
In Test mode, press button ＊ and then button 9 to enable arming with user code (default).
Total arming: enter a user code and press button
system state LED will light up and the keypad will beep.
Partial arming: enter a user code and press button
system state LED will blink four times and the keypad will beep three times.
Disarming: enter a user code and press button
light up and the keypad with beep twice.
Arming without user code
In Test mode, press button ＊ and then button 8 to enable arming without user code.
Total arming: press button
light up and the keypad will beep.
Partial arming: press button
blink four times and the keypad will beep three times.
Disarming: enter a user code and press button
light up and the keypad with beep twice.
Panic alarm
Press buttons 1 and 3 to activate the panic alarm. Press the user code to disarm it.
<
<
N
N
O
O
T
T
E
E
>
>
In default configuration, the panic alarm is off.
Main function overview
If alarms are stored, the blue state LED and the fault LED will light up and the keypad will beep five times.
Activate Test mode — Enter the keypad code and press button ＊.
8
E
>
E
>
: the keypad will generate a long beep.
to exit Test mode and complete the installation.
t
e
k
e
y
p
a
d
o
t
e
k
e
y
p
a
d
n
g
m
o
d
e
i
n
g
m
o
d
e
. If there are no faults and arming was successful, the red system state LED will
. If there are no faults and arming was successful, the red system state LED will
. If there are no faults and arming was successful, the red
. If there are no faults and arming was successful, the red
. If disarming was successful, the blue system state LED will
. If disarming was successful, the blue system state LED will
DS80KP55-001C
Werbung
Inhaltsverzeichnis
