Bresser 70-02520 Bedienungsanleitung Seite 15

NOTE!
When maximum or minimum reading is displayed, the corresponding
timestamp will be shown.
HI / LO ALERT
HI/LO alert are used to alert you of certain weather conditions. Once
activated, the alarm will turn on and amber LED starts flashing when
a certain criterion is met. The following are areas and type of alert
provided:
Bereich Verfügbarer Alarm-Typ
Indoor temperature HI AL / LO AL
Indoor humidity HI AL / LO AL
Outdoor temperaturw HI AL / LO AL
Outdoor humidity HI AL / LO AL
Rainfall HI AL*
Wind speed HI AL
*Daily rainfall since midnight
HI / LO alert setting (Fig. 29)
1. Press button several times until the desired area is selected.
2. Use or buttons to adjust the setting.
3. Press button to confirm and continue to next setting.
Fig. 29
Enable/Disable HI / LO alert (Fig. 30)
1. Press button several times until the desired area is selected..
2. Press button to turn the alert on or off.
3. Press button again to confirm and continue to next setting.
Fig. 30
NOTE!
1. The unit will automatically exit setting mode in 5 seconds if no
button is pressed.
2. When ALERT alarm is on, the area and type of alarm that triggered
the alarm will be flashing and the alarm will sound for 2 minutes.
3. Press SNOOZE/LIGHT button when alarm sounds to interrupt the
alarm. The alarm will then start again after 5 minutes.
4. Press button when alarm sounds to deactivate the alarm until
next time.
The alarm automatically turns off after 2 minutes.
WIRELESS SIGNAL RECEPTION
Fig. 31
No sensor Signal searching Strong signal
The 5-in-1 sensor is capable of transmitting data wirelessly over an
approximate operating of 150m range (line of sight).
Occasionally, due to intermittent physical obstructions or other
environmental interference, the signal may be weaken or lost.
In the case that the sensor signal is lost completely, you will need to
relocate the main unit or the wireless 5-in-1 sensor.
Weak signal Signal lost
POINTING 5-IN-1 SENSOR TO THE SOUTH
The outdoor 5-in-1 sensor is calibrated to be pointing to North
by default. However, in some cases, users may wish to install the
product with the arrow pointing towards the South, especially
for people living in the Southern hemisphere (e.g. Australia, New
Zealand).
1. First install the outdoor 5-in-1 sensor with its arrow pointing to the
South. (Please refer to 'Installation' chapter for mounting details)
2. Press and hold button for 8 seconds until the upper part
(Northern hemisphere) of the compass rose is blinking.
3. Use or button to change to lower part (Southern
hemisphere).
Fig. 32
Northern hemisphere
4. Press button again to confirm and exit.
DISPLAY COLOUR CHANGE
1. Press [ LOOP ] key to activate the automatic colour change.
Display changes continuously between 256 colours.
2. Press [ LOOP ] key again to disable colour change function. Press
[ RAINBOW ] key several times to select a colour from the
following and display it permanently: white > red > orange > yellow
> green > light-blue > deep blue > purple
3. Press [ LOOP ] key again to disable colour change function.
Press [ OUTDOOR TEMP ] key to run display colour change
depending on the outdoor temperature. The display colour
changes regarding to the values in the table below:
Temperature range Colour
under -20.0° C darkblue
-19.9° to -11.0° C lightblue 1
-10.9° to -5.0° C lightblue 2
-4.9° to -2.0° C lightblue 3
-1.9° to 1.0° C white
1.1° to 4.0° C lightgreen 1
4.1° to 8.0° C lightgreen 2
8.1° to 12.0° C yellow
12.1° to 16.0° C orange 1
TROUBLESHOOTING
Problem/Symptom Solution
Strange or no measurement 1. Check drain hole in the rain collector. Clean it
of rain sensor
2. Check the circular level. Realign the device if
Strange or no measurement 1. Check radiation shield. Clean it if neccessary.
of Thermo/Hygro Sensor 2. Check sensor housing. Clean it if neccessary
1. Relocate main unit and 5-in-1 sensor closer to
and --- (no signal for
15 minutes)
2. Make sure the main unit is placed away from
and ER (no Signal for
1 hour)
3. If problem continues reset both, main unit and
Southern hemisphere
Temperature range Colour
16.1° to 20.0° C orange 2
20.1° to 24.0° C orange 3
24.1° to 28.0° C red 1
28.1° to 32.0° C red 2
32.1° to 36.0° C pink 1
36.1° to 40.0° C pink 2
40.1° to 45.0° C purple
above 45.1° C
if neccessary.
neccessary.
each other.
other electronic appliances that may interfere
with the wireless communication (TV's,
computers, microwaves).
5-in-1 sensor.
gray
15