Safety Advice; Maintenance Instructions; Mounting Sequence - LAGUNA BADWELTEN Trento Montageanleitung

SAFETY ADVICE

• The mounting must only be done by experts.
• Warning: defective mounting is dangerous!
• Check whether the wall is suitable for the mounting and
that the fasteners are strong enough for the forces involved.
• Please read through the mounting instructions carefully
before mounting in the bathroom.
• The enclosed fastening material is only suitable for solid
walls of sufficient load-bearing strength.
• Electrical installations should only be carried out by a
specialist electrician DIN VDE 0100-701 (VDE 0100-701):2008-
10.
• Electrified, mirrored cabinets and flat mirrors must be locat-
ed at a minimum distance of 600 mm away from the bath or
shower.
• The safety regulations and standards of the particular coun-
tries must be observed.
IMPORTANT INFORMATION
• Inspect the packaging for external damage when it is delivered.
• Please check the number of bathroom cabinets supplied and
the associated sets of ironmongery (screws, cover caps,
handles, etc.) against the delivery note or the article's label
on the packaging.
• Caution: only remove the protective caps on the mirrored
cabinet's doors after mounting the doors, in order to avoid
damaging edges of the mirrors.
• Use suitable spacers or distance blocks to even out the
existing differences in level caused by coverings applied to
the walls, e.g., partial tiling.
• Reinforce any walls of insufficient load-bearing strength.
• The drilled dimensions are measured from the FFL according
to the dimensioned layout.
• Fasten the cabinets with the suspension rails:
- tall cabinets (600 mm width)
- Washstand base cabinet
- Middle cabinet with shelf
- Vanity unit with drawer
- shelves
• Always fasten the hanging bar to the wall with 2 screws!
• The horizontal spacing between the cabinets can be chosen
freely.
TOOLS
• Drill and battery-operated screwdriver
• Stone drill bit of 8 mm dia
• Wood drill bit of 4 mm dia
• Folding metre rule and measuring tape
• Spirit level
• Screwdriver with a 3.5 mm tip for Phillips screws
• Screw clamps
• Pencil
• Silicone sealant (transparent and solvent-free)
Trento

MAINTENANCE INSTRUCTIONS

• Caution: do not use any chemicals, aggressive detergent
paste or scouring powder.
• The best way of cleaning the cabinet is to use a damp cloth
with some mild washing-up liquid.
• Take care that no residue from droplets remains on the lower
edge of bathroom cabinets.
• Polish the mirror with a damp cloth or chamois leather.
• The washbasin can be easily cleaned with any of the usual,
non-abrasive cleaning agents.
• Ventilate regularly in order to prevent the mould from forming.
KEEP THE INSTRUCTIONS IN A SAFE PLACE
i
Caution: keep the instructions safely because they contain
information abouta installing and operating the products.

MOUNTING SEQUENCE

i
For the figures, see the attachment
1. Remove the doors and drawers (Fig. A/A1)
2. Mount the mirror grip (Fig. B)
3. Mount the lamps (Fig. C/C1/C2/C3)
The mains wire should not be live!
Do not overtighten the acryl panel light!
4. Mount the base and adjust height (Fig. D)
5. Hang up the furniture
· Mirror cabinet
(centre of the mirrored cabinet = centre of the water
supply connection)
· Tall cabinets, upper cabinet, centre cabinets, Base cabinet
· Highboard
· shelves
· Washstand vanity unit
6. Align furniture (Fig. E/E1/E2)
7. Mount the Washstand vanity unit (Fig. F)
8. Mount the washstand (Fig. G/G1)
9. Install the tap (Fig. H)
· Warning: Use the enclosed rubber seal.
· Do not overtighten the tap!
10. Screw on the shelf (Fig. I)
· Warning: Do not drill through the shelf!
· Use the enclosed screws.
11. Mount the doors and drawers (Fig. J/J1)
12. Align the doors and drawers (Fig. K/K1/K2/K3)
13. Mount the rollers (Fig. L)
14. Adjusting the folding hinge (Fig. M)
5