Your Device At A Glance; Assembly; Operation - Euromate 107446 Originalbetriebsanleitung

• The device must be mounted horizontally at a
height of at least 1.8 m above the floor. The
device must not be mounted to the cover or roof
incline.
• For operation of the device in the bathroom, the
safety distances must absolutely be adhered to
(► Safety distances – p. 9). It must be ensured
the people who are in the bathtub or shower can-
not reach the device.
• The device may not be operated outdoors.
• The device may never be operated without
supervision.
• Never put objects through the ventilation grate
into the device. Mortal danger!
• The distance between the front grate and flam-
mable objects must be at least 65 cm.
• The device may not be covered. There is danger
of fire.
• Never subject the device to water or other liquids.
• Do not use the heater in conjunction with a timer
or any other switch capable of automatic activa-
tion, as this creates a fire hazard.
• The heater must not be positioned beneath a wall
socket.
• Do not use adapters or extension cords.
• This appliance can be used by children aged
from 8 years and above and by persons with
reduced physical, sensory or mental capabilities
or lack of experience and knowledge if they have
been given supervision or instruction concerning
use of the appliance in a safe way and if they
understand the hazards involved. Children shall
not play with the appliance. Cleaning and user
maintenance shall not be made by children with-
out supervision.
• Children of less than 3 years should be kept
away unless continuously supervised.
• Children aged from 3 years and less than 8 years
shall only switch on/off the appliance provided
that it has been placed or installed in its intended
normal operating position and they have been
given supervision or instruction concerning use
of the appliance in a safe way and understand
the hazards involved. Children aged from 3 years
and less than 8 years shall not plug in, regulate
and clean the appliance or perform user mainte-
nance.
• CAUTION! Some parts of this product can
become very hot and cause burns. Particular
attention has to be given where children and vul-
nerable people are present.
• Symbols appearing on your device may not be
removed or covered. Signs on the device that are
no longer legible must be replaced immediately.
Read and observe the instructions for use
before using the product for the first time.
To prevent overheating, do not cover the
heater!

Your device at a glance

► Overview – p. 3
1. Heating rods
2. Front grate
3. Pull cord
4. Heat level indicator
Scope of delivery
• Wall radiator
• Screws and dowels for wall mounting (4 ×)

Assembly

Safety distances
DANGER! Risk of injury! For operation of
the device in the bathroom, the safety dis-
tances must absolutely be adhered to. It
must be ensured the people who are in the
bathtub or shower cannot reach the device.
► P. 3, item 1
The safety distances to the floor, walls, curtains, fur-
niture, etc. must always be adhered to.
Wall mounting
► P. 3, item 2
– 4 holes must be drilled in the wall, in accordance
with the dimensions given here, and insert
rawlplugs.
DANGER! Risk of electric shock! Before
drilling the holes, make sure that there are
no electrical or other cables running
through the wall at the relevant position.
DANGER! Risk of injury! The unit may
not be mounted directly below a wall
socket. Risk of cable fire!
DANGER! Risk of injury! Allow for the
device to cool down completely before set-
ting the angle of tilt.
– Loosen the screw (6) and remove the cover.
– Slot the supplied mounting screws through the
holes and screw into the drilled holes.
– Close the cover again.
– Plug the power cable of the unit into a grounded
socket.
– Set the required angle of tilt (20–40°).

Operation

Check before switching on!
DANGER! Risk of injury! The device
must only be put into operation if no faults
are found during the check-up. If any part of
the device is defective, it must be replaced
before the next use.
Check the safe condition of the device:
– Check whether there are any visible defects.
– Check whether all parts of the device are firmly
attached.
– Check whether the switch is on [0] before you
insert the plug into the outlet.
Switching on and off
– By pulling on the pull cord (3) several times, set
the desired heat level. The heat levels can be
read off of the heat level indicator (4) of the
device.
GB
9