Practical Tips - EINHELL TE-PL 18/82 Li Originalbetriebsanleitung

Fitting the parallel stop
•
Fasten the mount (d) of the parallel stop to
the left side of the tool using the supplied
thumb screw (a).
•
Now connect the mount (d) to the slide of the
parallel stop (11).
•
The guide rail must always be aligned in
downward direction.
•
Fix the distance required between the parallel
stop and the edge of the workpiece.
•
Fasten the parts with the carriage bolt (b) and
the wing nut (c).
5.4 Charging the LI battery pack (Fig. 13-14)
1. Remove the battery pack (a) from the handle,
pressing the pushlock buttons (c) downwards
to do so.
2. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Insert the power plug of the charger
(b) into the mains socket outlet. The green
LED will then begin to fl ash.
3. Push the battery pack onto the battery char-
ger.
In section 10 "Charger indicator" you will fi nd a
table with an explanation of the LED indicator on
the charger.
If the battery pack fails to become charged, ple-
ase check
•
whether there is voltage at the socket-outlet
•
whether there is proper contact at the char-
ging contacts on the charger.
If the battery still fails to become charged, please
return
•
the charger
•
the battery pack
to our Customer Service Department.
To ensure that items are properly packaged
and delivered when you send them to us,
please contact our customer service or the
point of sale at which the equipment was
purchased.
When shipping or disposing of batteries and
cordless tools, always ensure that they are
packed individually in plastic bags to prevent
short circuits and fi res.
To ensure that the battery pack provides long ser-
vice, you should take care to recharge it promptly.
You must recharge the battery pack when you
Anl_TE_PL_18_82_Li_SPK9.indb 19 Anl_TE_PL_18_82_Li_SPK9.indb 19
GB
notice that the performance of the device drops.
Never allow the battery pack to become fully di-
scharged. This will cause it to develop a defect.
5.5 Battery capacity indicator
(Fig. 13 – Item e)
Press the battery capacity indicator switch (d).
The battery capacity indicator (e) shows the char-
ge status of the battery using 3 LEDs.
All 3 LEDs are lit:
The battery is fully charged.
2 or 1 LED(s) are lit:
The battery has an adequate remaining charge.
1 LED blinks:
The battery is empty, recharge the battery.
All LEDs blink:
The battery pack has undergone exhaustive di-
scharge and is defective. Do not use or charge a
defective battery pack.
6. Operation
6.1 ON/OFF switch (Fig. 5)
•
The plane comes with a safety switch which
is designed to prevent accidents.
•
To switch on the tool, press the side safety
lock-off (3) and press the button switch.
•
Release the button switch (4) to switch off the
plane. The button switch (4) jumps back into
its starting position.

6.2 Practical tips

Warning! Only ever bring the plane towards the
workpiece while switched on.
6.2.1 Planing surfaces
Now adjust the desired chip depth. Equip the front
base plate and place the plane onto the piece of
wood you wish to plane. Then switch on the plane.
Push the plane over the surface with both hands
and make sure that the both the front and the rear
base plate lie fl at on the workpiece. Used a low
chip depth for fi nishing surfaces and complete
several passes over the surface.
6.2.2 Chamfering edges (Fig. 6-7)
•
There is a V-shaped groove (a) in the front
base plate that enables you to plane edges at
an angle of 45° for a smooth finish.
- 19 -
21.04.2020 15:08:24 21.04.2020 15:08:24