Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Operation using a 3-key radio control (BeFree x3 - X6):
Using the BeFree x3 – x6 radio control ensures the same oper-
ation as for the BeFree x1 version. The radio control's two side
keys, (-) and (+), also allow you to select commands (Up – Stop
– Down) for 3 different utilities (BeFree x3) or 6 different utilities
(BeFree x6). Pressing and holding the two side keys (-) and (+)
for a few seconds also enables and disables operation of the
sun sensor (the selection is confirmed by a quick Up/Down
movement of the motor).
Z
G
C
ONE AND
ENERAL
Centralization with cable and keys
The centralization of two or more control units via wire enables
simultaneous raising or lowering of the connected shutters. To
do this you need to connect the control units with a bus of three
wires in parallel to the inputs of the General UG (Up) and DG
(Down) commands and the "GND Signal" common reference.
This allows you to control the 4 motors independently or simul-
taneously with the UZ (Up) and DZ (Down) zone commands
and centralize other control units with the UG (Up) and DG
(Down) general commands.
A
NEMOMETER OPERATION
The electronic control unit raises the sun shade whenever the
wind exceeds the selected threshold.
S
S
UN
ENSOR OPERATION
The electronic control unit lowers the sun shade after 10
minutes of brightness greater than the Sun Sensor's selected
threshold; this is indicated by the SUN LED which lights up.
The control unit then raises the blind after 10 minutes during
which the brightness is below the selected threshold.
R
S
AIN
ENSOR OPERATION
The electronic control unit raises the blind as soon as the sensi-
tive part of the rain sensor is touched by water. The RAIN LED
lights up.
P
K
ROGRAMMING
EYS AND
SEL key: this selects the function to be stored. The LED flash-
es to indicate your selection. Keep pressing the key to find the
required function. The selection remains active for 15 seconds
(during which time the LED keeps flashing) after which the con-
trol unit then returns to its original state.
SET key: this key programs the function selected with the SEL
key.
Indicator LED
LED on: stored option.
LED off: option not stored.
LED flashing: option selected.
---------------------- MAIN MENU -----------------
LED reference
LED off
1) CODE M1
No code
2) CODE M2
No code
3) CODE M3
No code
4) CODE M4
No code
5) CODE SENS.
No code
6) T. MOT.
Motor time 2 min.
7) WIND SPEED
Wind safety 25 Km/h
8) SUN SENSOR Sun sensor = OFF
9) RAIN SENSOR Rain sensor = OFF
10) SUN
Presence of Sun = No
11) RAIN
Presence of Rain = No
10) CODE M1 (Programming the radio control for Motor 1)
Programming the 1 or 2 key radio control.
The radio control transmission codes are programmed as fol-
lows: press the SEL key and M1 CODE LED will start flashing;
ENTRALIZATION
I
L
NDICATOR
ED
LED on
Code TX Pgm. M1
Code TX Pgm. M2
Code TX Pgm. M3
Code TX Pgm. M4
Code Pgm. sensors
Motor time Pgm.
Wind safety Pgm.
Sun sensor = ON
Rain sensor = ON
Presence of Sun = Yes
Presence of Rain = Yes
at the same time send the first pre-selected code with the re-
quired radio control: M1 CODE LED will start flashing quickly;
send the second code to be stored, M1 CODE LED remains
ON and programming will be complete. If the second code is
not send within 10 seconds, the control unit exits the program-
ming phase, selecting operation with 1 key of the radio control.
If all the codes are stored and you try to repeat the program-
ming phase, all the indicator LEDs will start flashing very quick-
ly to indicate no more codes can be stored.
Programming the "BeFree" 3-key radio control
The entire "BeFree" radio control can be configured by pro-
gramming just the Up Key.
The "BeFree" radio control's codes are programmed as follows:
press the SEL key and M1 CODE LED will start flashing; at the
same time, press the UP key on the required radio control. At
the same time, M1 CODE LED remains ON and programming
will be complete. If all the possible radio controls have been
stored and you try to repeat the programming phase, all the in-
dicator LEDs will start flashing very quickly to indicate no more
codes can be stored.
11) CODE M2 (Programming the radio control for Motor 2)
Follow the CODE M1 instructions in paragraph 1) above to pro-
gram the radio control for motor 2, initially pressing the SEL key
twice.
12) CODE M3 (Programming the radio control for MOTOR 3)
Follow the CODE M1 instructions in paragraph 1) above to pro-
gram the radio control for motor 3, initially pressing the SEL key
three times.
13) CODE M4 (Programming the radio control for MOTOR 4)
Follow the CODE M1 instructions in paragraph 1) above to pro-
gram the radio control for motor 4, initially pressing the SEL key
four times.
CODE ALL (Programming the radio control for all 4 motors)
Follow the CODE M1 instructions in paragraph 1) above to pro-
gram the radio control for all four motors, initially pressing the
SEL key five times.
14) CODE SENS. (Programming the wireless sensors)
Programming the Wireless sensor (Sun – Wind – Rain).
The Wireless Sensor's transmission code is programmed as
follows: use the SEL key to select the flashing SENS CODE
LED; at the same time, send the Wireless Sensor code via the
dedicated key situated inside the sensor. SENS CODE LED
stays ON and programming will be complete. If the Wireless
Sensor code is not sent within 2 minutes, the control unit exits
the programming phase. If all the possible Wireless Sensor
codes are already on the memory, all the indicator LEDs will
start flashing very quickly during the programming operation to
indicate no more codes can be stored.
Deleting the codes
Stored Wireless Sensor codes are deleted as follows: press the
SEL key and SENS CODE LED will start flashing; next, press
the SET key and SENS CODE LED will switch off, and the pro-
cedure is complete.
Signalling
Should there be no communication between the Wireless Sen-
sor and the control unit for 20 minutes, the shutter is automati-
cally raised as a safety precaution. If communication continues
to be down, other controls will in any case always keep the con-
trol unit in safe mode.
15) LED T. MOT. (Programming Motor Time, max 4 minutes)
The control unit comes with a motor power time set at two
minutes (LET T.MOT. OFF).
The motor time must be programmed as follows when the shut-
ter is down:
Press the SEL key until the LED T.MOT key flashes, then press
9
Rev. 3.0
13/06/16
Werbung
