Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Grinding
Vibration a
h
Uncertainty K
h
9. Unpacking
• Open the packaging and remove the device care-
fully.
• Remove the packaging material as well as the
packaging and transport bracing (if available).
• Check that the delivery is complete.
• Check the device and accessory parts for transport
damage. Inform the transport agent immediately of
any faults. Later complaints cannot be considered.
• If possible, store the packaging until the warranty
period has expired.
• Familiarize yourself with the machine with the help
of the operating instructions manual before using it.
• Use only original parts for accessories as well as
consumables and spare parts. Spare parts can be
obtained from your scheppach retailer.
• Please quote our article numbers as well as type
and production year in all your orders.
m ATTENTION!
The device and packaging materials are not toys!
Children must not be allowed to play with plas-
tic bags, film and small parts! There is a risk of
swallowing and suffocation!
10. Assembly
CAUTION:
• Always make sure that the machine is switched off
and the battery removed before carrying out any
work on the machine.
Fitting and removing the application tool (Figs.
2 and 3 )
WARNING:
• Do not fit the application tool upside down. If an
application tool is fitted the wrong way round, it can
damage the machine and cause serious injury.
• Fit the application tool in the correct direction ac-
cording to the work to be done. The application tool
can be fitted in positions offset by 30 degrees.
CAUTION:
• Be careful when closing the locking lever. The lock-
ing lever may suddenly close and pinch a finger.
• The moving part of the locking lever must be reg-
ularly cleaned of dust and lubricated. Otherwise,
dust may accumulate on the moving part of the
locking lever and impede its smooth movement.
• Do not start the tool while the lever is opening. Oth-
erwise the tool may be damaged.
www.scheppach.com / service@scheppach.com / +(49)-08223-4002-99 / +(49)-08223-4002-58
5,1 m/s²
1,5 m/s²
1) Open the locking lever fully. And remove the re-
taining screw.
2) Place the application tool (optional accessory) on
the tool flange so that the protrusions of the tool
flange fit into the holes of the application tool.
3) Insert the retaining screw as far as it will go. Then
return the locking lever to its original position.
If using an application tool for sanding, fit the ap-
plication tool to the sanding pad so that it matches
the direction of the pad. The sanding pad features a
Velcro fit system that allows comfortable and quick
application of sandpaper. Since sandpaper has holes
for dust extraction, fit the sandpaper so that its holes
coincide with those in the sanding pad. To remove the
sandpaper, lift its edge and remove the paper.
To remove the retaining screw, use the assembly pro-
cedure in reverse.
If using application tools with a different type of in-
stallation part, select a correct adapter (optional ac-
cessory).
11. Installation
To ensure that the Li battery pack provides long ser-
vice you should take care to recharge it promptly. You
must recharge the battery pack when you notice that
the power of the cordless equipment drops.
Always make sure that the machine is switched off
before inserting the battery into the machine.
Insertion / removal of a batterypack into the ap-
pliance
Ensure that the appliance is switched off before in-
serting the battery. The insertion of a battery into an
electrical appliance that is switched on can lead to
accidents.
Inserting the rechargeable battery pack:
Push the rechargeable battery pack into the handle
until it engages.
Removing the rechargeable battery pack:
Press the release button and remove the rechargea-
ble battery pack.
Used batteries
If a fully recharged battery lasts for considerably
shorter operating times, the battery is used up and
needs to be replaced. Only use an OEM battery pack
replacement available from our Customer Service.
Switching on and off
To switch on the machine, slide the slide switch to
position "I (ON)".
GB | 21
Werbung
Kapitel
Fehlerbehebung
