Important Note - OKBABY Flat Anleitung

INsTrucTIONs FOr THE OKBABY FLAT cHANgINg
EN
TABLE cOdE NO. 839
WArNINg!!!
NEvEr LEAvE THE cHILd uNATTENdEd
ImPOrTANT: Please read the following instructions carefully
before use and keep them for future reference.
mAXImum BABY WEIgHT 15Kg.
FLAT changing table can be adapted for use in different situations: on a stable table, on a cot or
over a bathtub.
Product dimensions: 66.2 cm x 84.6 cm x 18.3 cm.
usINg FLAT ON A sTABLE TABLE Or WOrK surFAcE
(minimum surface area 67 cm x 85 cm)
1. Fold away Flat supports making sure that they are blocked by the lock on the side under-
neath the changing area (fig. 1).
2. Place FLAT on a flat, stable surface (fig. 2).
3. Make sure that all the non-slip feet (fig. 3) are touching the table or work surface to ensu-
re maximum stability.

ImPOrTANT NOTE:

• FLAT cannot be positioned on all types of table.
Do not use it on tables with sliding tops, fold-away tables, single-leg tables, games tables
or collapsible tables.
• Do not place towels or other items on the supporting surface that may interfere with the
proper functioning of the non-slip feet. Make sure the structure and the surface of the ta-
ble are kept clean and dry.
• Do not move FLAT with the baby on it.
usINg FLAT OvEr A BATHTuB
(minimum internal width of bathtub 56 cm, maximum 74 cm)
1. Release the side lock underneath the changing area to free FLAT supports (fig. 4).
2. Open FLAT supports completely, making sure that the red clasps hook completely into
place on the sides of the changing table (fig. 5).
3. Adjust the feet of each Flat support to the minimum width (fig.11).
4. Position FLAT over the bathtub to rest on the side edges (fig. 6).
5. Adjust the feet of the supports so that the non-slip rubber pads rest against the inside
wall of the bathtub and the suction cups rest on the top of the bathtub edges (fig. 7).
6. To close FLAT supports, press the sides of each red hook (fig. 5) pushing the changing
table's supports inward and hook them in place on the side lock underneath the changing
area (fig. 1).
ImPOrTANT NOTE:
• Make sure that the internal width of the bathtub, as shown in fig.15, measures at least 56 cm.
• Always check that the changing table is in the correct position on the bathtub and that
the fixing devices are correctly adjusted before placing the baby on the changing table.
• Position FLAT over the bathtub so that the baby cannot reach the taps.
• If the bathtub is not positioned against a wall, place FLAT centrally over it (fig. 13).
• Other children must not be allowed in the bathtub while the changing table is in position
for use.
• Do not move FLAT with the baby on it.
6.Flat
usINg FLAT ON THE TOP-rAILs OF A cOT
(maximum external width of the cot 63 to 73.5 cm).
1. Fold away Flat supports making sure that they are blocked by the lock on the side under-
neath the changing area (fig. 1).
2. Place FLAT on the cot (fig. 8), taking care to ensure that the notch is positioned over the
top-rail of the cot (fig. 14).
3. FLAT must be fixed to the top-rails of the cot by the three Velcro straps supplied, one at
the back and two at the front of the changing table.
4. Thread the strap through the slot on the bottom edge of the changing table (fig. 9), pass it
under the top-rail of the cot and secure with Velcro (fig.10). Repeat for the other two an-
chor points.
ImPOrTANT NOTE:
• Before proceeding to use the product on a home cot, make sure that it is perfectly sup-
ported by the two top rails and that it is fastened securely with the three straps provided.
Verify the stability of FLAT before resting your child there.
• The straps provided should only be used for securing the changing table to the baby's cot
and should be immediately removed afterwards to avoid risk of entangling or obstruction.
• If the cot has adjustable top-rails, make sure that these are completely locked into place
before using FLAT.
• Do not move FLAT with the baby on it.
WArNINg!
• Always be aware of the risks associated with open flames or other sources of high heat,
such as electric hot plates, gas flames, etc., close to the changing table.
• FLAT is designed for babies with a max. weight of 15 kg.
• Do not use FLAT if anything appears to be broken or missing.
• Clean FLAT with a soft cloth and a neutral detergent. Do not use abrasive cleaners, sol-
vents or ammonia-based products.
• Any optional or spare parts must be ordered from the manufacturer or distributor.
Flat.7