Troubleshooting - Sharp HT-SBW800 Handbuch

• When the PCM audio format is being used, the Soundbar display shows
PCM AUDIO.
• When being used non-PCM or DOLBY DIGITAL audio formats, if there's
no sound output from the unit and the display show NO SUPPORT.
Bluetooth Operation
Pair Bluetooth-enabled Devices
The fi rst time you connect your bluetooth device to this player, you need to
pair your device to this player.
NOTE:
– The operational range between this player and a Bluetooth device is
approximately 8 meters (without any object between the Bluetooth
device and the unit).
– Before you connect a Bluetooth device to this unit, ensure you know
the device's capabilities.
– Compatibility with all Bluetooth devices is not guaranteed.
– Any obstacle between this unit and a Bluetooth device can reduce the
operational range.
– If the signal strength is weak, your Bluetooth receiver may disconnect,
but it will re-enter pairing mode automatically.
1. During ON mode, press the
button on the remote control to select Bluetooth mode. "NO BT" will
show on the display if the unit is not paired to any Bluetooth device.
2. Activate your Bluetooth device and select the search mode.
"HT-SBW800" will appear on your Bluetooth device list.
– If you cannot fi nd the unit, press and hold the button on the remote
control to be searchable. The display will show "PAIR" and you will hear
"Pairing" from the unit.
3. Select "HT-SBW800" in the pairing list. After successful pairing, you will
hear "Paired" from the unit, and the display panel shows "BT".
4. Play music from the connected Bluetooth device.
To disconnect the Bluetooth function, you can:
– Switch to another function on the unit.
– Disable the function from your Bluetooth device.The Bluetooth device
will be disconnected from the unit after the "Disconnected" voice
prompt.
– Press and hold the button on the remote control.
TIPS:
• Enter "0000" for the password if necessary.
• If no other Bluetooth device pairs with this player within two minutes,
the player will recover its previous connection.
• The player will also be disconnected when your device is moved beyond
the operational range.
• If you want to reconnect your device to this player, place it within the
operational range.
• I f the device is moved beyond the operational range, when it is brought
back, please check if the device is still connected to the player.
• If the connection is lost, follow the instructions above to pair your device
to the player again.
Listen to Music from Bluetooth Device
– If the connected Bluetooth device supports Advanced Audio Distri-
bution Profi le (A2DP), you can listen to the music stored on the device
through the player.
– If the device also supports Audio Video Remote Control Profi le (AVRCP),
you can use the player's remote control to play music stored on the
device.
1. Pair your device with the player.
2. Play music via your device (if it supports A2DP).
3. Use supplied remote control to control play (if it supports AVRCP).
– To pause/resume play, press the
on the unit.
– To skip to a track, press the
button repeatedly on the unit or the
button on the remote control or
/ buttons on the remote control.
USB Operation
1. Insert the USB device.
2. Press the button repeatedly on the unit or press the
the remote control to select USB mode.
3. During playback:
– To pause or resume play, press the
– To skip to the previous/next fi le, press the
remote control.
TIPS:
• USB devices up to 32GB are supported.
• Only MP3 fi les can be played back.

Troubleshooting

No power
• Ensure that the AC cord of the soundbar and subwoofer are correctly
connected.
• Ensure that there is power at the AC outlet.
• Press (standby) button to turn the unit on.
Remote control does not work
• Before you press any playback control button, fi rst select the correct
source.
• Reduce the distance between the remote control and the unit.
• Insert the battery with its polarities (+/-) aligned as indicated.
• Replace the battery.
• Aim the remote control directly at the sensor on the front of the unit.
No sound
• Make sure that the unit is not muted. Press MUTE or VOL+/VOL– button
to resume normal listening.
• Press button on the unit or on the remote control to switch the soundbar
to standby mode. Then press the button again to switch the soundbar
on.
• Unplug both the soundbar and the subwoofer from the mains socket,
then plug them again. Switch on the soundbar.
• The unit may not be able to decode all digital audio formats from the
input source. In this case, the unit will mute. This is NOT a defect. Ensure
the audio setting of the input source (e.g. TV, game console, DVD player,
etc.) is set to bitstream while using digital (e.g. HDMI, OPTICAL, COAXIAL)
connection. For Sharp TV brands please select "RAW" or "Auto" option in
the digital output menu.
• The subwoofer is out of range, please move the subwoofer closer to the
soundbar. Make sure the subwoofer is within 5 m of the soundbar (the
closer the better).
• The soundbar may have lost connection with the subwoofer. Re-pair
the units by following the steps on the section "Pairing the Wireless
Subwoofer with the Soundbar".
TV has display problem while viewing HDR content from HDMI source.
EN
button on
button on the remote control.
/ buttons on the