Basic Operation; Pairing The Wireless Subwoofer With The Main Unit - Sharp HT-SBW800 Handbuch

6
Connect Power
Risk of product damage!
• Ensure that the power supply voltage corresponds to the voltage printed
on the back or the underside of the unit.
• Before connecting the AC power cord, ensure you have completed all
other connections.
Soundbar
• Unwind the mains adapter and mains cable to their full length.
• Connect power cord to the power adapter, then connect power adapter
to the DC IN 23V socket of the unit and as last step connect it into a
mains socket.
Subwoofer
• Connect the mains cable to the AC~ Socket of the Subwoofer and then
into a mains socket.
Pairing the Wireless Subwoofer with the
Main Unit
Automatic pairing
The subwoofer and soundbar will pair automatically when both are
plugged into the mains supply. Connection is wireless, so there is no need
for any cables to connect the two units.
• When the subwoofer is pairing with the main unit, the Pair Indicator will
fl ash quickly.
• When the subwoofer is paired with the main unit, the Pair Indicator will
light up.
NOTE:
– Only press the Pair button on the rear of the Subwoofer if pairing
manually.
– If the automatic pairing fails, pair the subwoofer with the main unit
manually.
Manual pairing
1. Ensure that all the cables are well connected and the main unit is in
Standby mode.
2. Press and hold the Pair button on the rear of the subwoofer for a
few seconds. The subwoofer will enter the pairing mode and the Pair
Indicator will blink quickly.
3. Press the button on the main unit or on the remote control to switch
the main unit on.
4. When the subwoofer and soundbar have paired, the Pair indicator will
illuminate.
5. If the Pair indicator blinks, the wireless connection has failed. Unplug
the cable of the subwoofer and then reconnect the main cable after 4
minutes. Repeat step 1 ~ 4.
NOTE:
• If the wireless connection fails again, check if there is confl ict or strong
interference (for example, interference from an electronic device) around
your location. Remove these confl icts or strong interferences and repeat
the above procedures.
• The subwoofer should be within 5m of the soundbar in an open area.
• If the main unit is not connected with the subwoofer and it is in On
mode, the POWER Indicator will fl ash. Follow step 1 ~ 4 above to pair the
subwoofer to the main unit.
EU

Basic Operation

EU
Standby/ON
UK When you fi rst connect the main unit to the mains socket, the main unit
will be in Standby mode.
• Press the button on the unit or on the remote control to switch the
unit ON.
• Press the button again to switch the unit back to STANDBY mode.
• Disconnect the mains plug from the mains socket if you want to switch
the unit OFF completely.
– If a TV or an external device is connected, the unit will switch on auto-
matically when the TV or the external device is switched on.
– When there is no input signal from the unit in over 15 minutes, then it
will automatically switch to Standby mode.
Select Modes
Press the button repeatedly on the unit or the
the remote control to select the AUX, OPTICAL, COAXIAL, HDMI 1, HDMI
2, HDMI ARC, USB and BT (Bluetooth) mode. The selected mode will show
on the display.
Adjust the Bass / Treble
• Press the BASS+/- button on the remote control to adjust bass level.
• Press the TREBLE+/- button on the remote control to adjust treble level.
Turn the Surround Sound ON/OFF
• Press the SURROUND button on the remote control to turn on the
surround sound. Press this button again to turn off the surround sound.
Adjust the Volume
• Press the VOL+ / VOL- buttons on the unit or on the remote control to
adjust the volume.
• If you wish to turn the sound off , press the
control. Press the
the unit or on the remote control to resume normal listening.
Select Equaliser (EQ) Eff ect
• While playing, press the EQ button on the remote control to select
between preset equalisers: Movie (recommended for viewing movies),
Music (recommended for listening to music), News (recommended for
listening to News), Night (recommended for listening at night).
AUX / OPTICAL / COAXIAL / HDMI / HDMI
ARC Operation
1. Ensure that the unit is connected to the TV or audio device.
2. Press the button repeatedly on the unit or the
on the remote control to select the AUX, OPTICAL, COAXIAL, HDMI 1,
HDMI 2, HDMI ARC mode.
3. Operate your audio device directly for playback features.
4. Press the VOL +/– button to adjust the volume to your desired level.
TIP:
• The unit may not be able to decode all digital audio formats from the
input source. In this case, the unit will mute. This is NOT a defect. Ensure
that the audio setting of the input source (e.g. TV, game console, DVD
player, etc.) is set to PCM or Dolby Digital (Refer to the user manual of
the input source device for its audio setting details) with HDMI 1 /HDMI 2
/ HDMI ARC / OPTICAl / COAXIAL input.
• When the DOLBY DIGITAL audio format is being used, the Soundbar
display shows DOLBY AUDIO.
/ HDMI / buttons on
button on the remote
button again or press the VOL+ / VOL- buttons on
/ HDMI buttons