Inhaltszusammenfassung für HANSGROHE Metris Select M71 320 2jet sBox 73816003
Seite 1
DE Gebrauchsanleitung / Montageanleitung EN Instructions for use / assembly instructions Metris Select M71 320 2jet sBox 73816003...
Seite 2
Serviceteile (siehe Seite 16) linien sind einzuhalten. • Bei Erstinbetriebnahme und nach Wartungsarbeiten Sonderzubehör kann es durch Luft in der Armatur zu einem Geräusch kommen. Nach ca. 15 Aktivierungen der Armatur ist (nicht im Lieferumfang enthalten) das Geräusch verschwunden. F12 Verlängerung #43333000 Technische Daten (siehe Seite 16 / 17) Betriebsdruck: max. 1 MPa Empfohlener Betriebsdruck: 0,1 - 0,5 MPa Bedienung (siehe Seite 12) Prüfdruck: 1,6 MPa • Hansgrohe empfiehlt, morgens oder nach längeren (1 MPa = 10 bar = 147 PSI) Stagnationszeiten den ersten halben Liter nicht als Heißwassertemperatur: max. 70°C Trinkwasser zu verwenden. Empfohlene Heißwassertemperatur: 65°C • Beim Öffnen der Armatur über den Hebelgriff kann Thermische Desinfektion: max. 70°C / 4 min kurzzeitig minimal Wasser am Auslauf austreten. Das Produkt ist ausschließlich für Trinkwasser konzipiert! • Über den Hebelgriff wird die Armatur geöffnet und Symbolerklärung die gewünschte Temperatur eingestellt. Durch den stirnseitig am Auslauf befindlichen Select-Knopf kann Kein essigsäurehaltiges Silikon verwenden! der Wasserfluss pausiert werden. Bei längerer Nichtverwendung, z. B. über Nacht oder bei...
• Prior to installation, inspect the product for transport Cleaning (see page 13) damages. After it has been installed, no transport or surface damage will be honoured. Spare parts (see page 16) • The pipes and the fixture must be installed, flushed and tested as per the applicable standards. Special accessories (order as an extra) • The plumbing codes applicable in the respective F12 extension #43333000 (see page 16 / countries must be observed. • During initial start-up and after servicing, air in the fittings can cause noise. After switching the jet on Operation (see page 12) and off about 15 times, the noise will stop. • Hansgrohe recommends not to use as drinking water Technical Data the first half liter of water drawn in the morning or Operating pressure: max. 1 MPa after a prolonged period of non-use. Recommended operating pressure: 0,1 - 0,5 MPa • Minor leaking may occur briefly at the spout when Test pressure: 1,6 MPa opening the fitting via the lever. (1 MPa = 10 bar = 147 PSI) • Use the lever to open the tap and set the desired Hot water temperature: max. 70°C temperature. The water flow can be paused by Recommended hot water temp.:...
Seite 4
(3 Nm) SW 24 mm (4 Nm) 150° 110° SW 10 mm SW 19 mm (4 Nm)
Seite 5
150° 75° 75° 24 x 15° 105° 45° 105° 45°...
Seite 6
110° 55° 55° 110° 24 x 15° 85° 25° 85° 25°...
Seite 7
SW 22 mm SW 17 mm 96507000 (450 mm) SW 19 mm (4 Nm) SW 22 mm SW 22 mm SW 17 mm (8 Nm)