Velleman VTSS5 Bedienungsanleitung Seite 4

3. Ge eneral Guid delines
Refer to the Velleman n® Service an
Indoor r use only. Ke
dripping
Keep th his device away
opening gs are clear at
Protect
device.
• Fami iliarise yoursel
• All m modifications of f the device are
mod ifications to th
• Only y use the device
the w warranty.
• Dam mage caused by y disregard of c
warr ranty and the d dealer will not a
• Do n not switch the d device on imm
Prote ect the device
temp perature.
4. Ov verview
Refer to the illustration ns on page 2 o
1 po
2 te emperature con
3 sp ponge
4 iro
5. Ins structions s
a. Prep paration
• Put the solderin P ng iron holder
station. s
• Make sure the M
before you put b
• P Put the solderin ng tip [5] into
c coupling nut. O Only change a s
the coupling nu t ut and gently p
t tighten it when
War rning: Never u use the solde
b. Elec ctrical Connec ction
• Connect the po C ower cord [1] t
the soldering st t
c. Tem mperature sett
• U Use the rotary
t temperature.
• S Set the temper rature controlle
m moments and t try to melt som
controller [2] a c a little further c
d. Ope ration
• P Prerequisite for r clean joints is
station. We rec s commend the u
s should not be u used in any cas
Switch on the s S soldering statio
t temperature of f 200°C (tempe
07.12.20 010
All manuals and user guides at all-guides.com
VTSS5
nd Quality Wa
eep this device
g liquids. Neve er put object fil
y from dust an
all times.
this device fro om shocks and
f with the func ctions of the de
e forbidden for
e device is not t covered by th
e for its intend ded purpose. U
certain guidelin
accept respons
ediately after i
against damag ge by leaving it
of this manual.
ower cord
ntroller
on stand
[4] in the corr
sponge [3] is completely sat
it in the spong ge tray.
the shaft [6]
soldering tip w
pull out the sold
necessary.
ering iron with
to a 230V/50H
tation is now r eady for use.
ting
control [2] on n the front pane
er [2] between
me solder. If it
clockwise, wait
s the use of su
use of solder w
se. Before the
on and apply so
erature control
arranty on the e last pages of
away form rai n, moisture, s
lled with liquid on top.
nd extreme hea at. Make sure t
abuse. Avoid brute force wh
evice before ac ctually using it.
r safety reason ns. Damage cau
he warranty.
sing the device e in an unauth
nes in this man nual is not cove
sibility for any ensuing defect
it has been exp posed to chang
t switched off u until it has reac
5 5 bit
6 6 heating ele ement
7 7 antiskid rub bber
8 8 handle
responding hol e in the casing
turated with cle ean water and
and attach it t o the soldering
hen the solder ring iron has co
dering tip. Che eck the screw f
hout the sold ering tip.
z power supply y. The power L
el to switch the e device on an
n the second an nd third scale,
doesn't melt fl luidly, rotate th
t a little while a and try again u
ited solder and d a correct use
with a resin flux x core. Halogen
first uses, you should tin the
ome solder to the soldering t
ler between sc cale 2 and 3). P
4
Rev v. 02
this manual.
plashing and
the ventilation
hen operating t the
used by user
orised way wil l void
ered by the
ts or problems .
ges in tempera ture.
ched room
g of the solderi ng
let it drip off
g iron with a
ooled down. Lo oosen
fitting regularly y and
LED turns ON a and
d set the desir red
wait a few
he temperature e
until it does.
of the solderin ng
n containing so older
e new soldering g tip.
tip at a
Perfect joints a are
©Vellem man nv