Nelle tabelle 10.13 "Campo di applicazione" è
segnalato in modo inequivocabile quando le
condizioni operative sono tali da richiedere il
raffreddamento dell'olio.
1000
100
10
20
diagramma viscosità-temperatura
fig. 6
5. Il lubrificante
L'olio iniettato tra le viti e nei cuscinetti, oltre a
provvedere alla loro lubrificazione, agisce da
sigillante tra i profili delle viti; ne risulta che è
molto importante che il lubrificante risponda a
precise caratteristiche di viscosità e solubilità.
È quindi essenziale che venga impiegato
esclusivamente lubrificante approvato da
FRASCOLD.
5.1
Caratteristiche del lubrificante
Lubrificante FRASCOLD FCL
refrigerante
R407C / R134a
viscosità cinematica:
a 40°C
a 100°C
punto di accensione
densità
Lubrificante FRASCOLD FCH
refrigerante
viscosità cinematica:
a 40°C
a 100°C
punto di accensione
densità
5.2
Raccomandazioni
•
I limiti di impiego del compressore non
devono essere superati in nessuna
condizione operativa
In the tables 10.13 "Application limits",
are unmistakably showed the working conditions
when oil cooling must be performed.
30
40
temperatura dell'olio °C - oil temperature °C - Öltemperatur °C
viscosity-temperature diagram
5. The lubricant
The oil injected to the screws not only lubricates
but also provide to seal the gap between the
screw profiles.
In order to ensure an excellent lubrication of the
compressor, are necessary suitable
characteristics of viscosity and solubility.
It is essential to use only lubricants approved by
FRASCOLD.
5.1
Lubricant data
Lubricant FRASCOLD FCL
refrigerant
kinematics viscosity:
cSt 150
at 40°C
cSt 14.5
at 100°C
°C 252
flash point
g/ml 0.96
density
Lubricant FRASCOLD FCH
R22
refrigerant
kinematics viscosity:
cSt 150
at 40°C
cSt 14.5
at 100°C
°C 252
flash point
g/ml 0.96
density
5.2
Recommendations
•
application limits are to be considered
values not to exceed in every working
conditions.
50
60
70
fig. 6
R407C / R134a
cSt 150
cSt 14.5
°C 252
g/ml 0.96
R22
cSt 150
cSt 14.5
°C 252
g/ml 0.96
10
werden
die
Betriebsbedingungen
unmißverständlich dargelegt, bei denen das Öl
gekühlt werden muß.
80
90
10O
Viskosität-Temperaturschaubild
Abb. 6
5. Schmiermittel
Das auf die Schrauben und die Lager
eingespritzte Schmiermittel dient nicht nur zur
Schmierung
sondern
dichtet
Schraubenprofile ab.
Es ist sehr wichtig das, der Schmiermittel spezifische
Eigenschaften von Löslichkeit und Viskosität hat.
Bitte benutzen nur von FRASCOLD geprüfte
Schmiermittel.
5.1
Schmiermitteleigenschaften
Schmiermittel FRASCOLD FCL
Kältemittel
R407C / R134a
Kinematische Viskosität:
bei 40°C
bei 100°C
Flammpunkt
Dichtigkeit
Schmiermittel FRASCOLD FCH
Kältemittel
Kinematische Viskosität:
bei 40°C
bei 100°C
Flammpunkt
Dichtigkeit
5.2
Ausführungshinweise
•
die Verdichter Anwendungsgrenzen
sollen unter keiner Bedingung
übergeschritten sein
die
cSt 150
cSt 14.5
°C 252
g/ml 0.96
R22
cSt 150
cSt 14.5
°C 252
g/ml 0.96