Panasonic DVD-LS83 Bedienungsanleitung Seite 15

Connecting the included Car DC Adaptor
Before connection, consult your car owner's manual or your dealer.
≥ Connect to the cigarette lighter socket of a vehicle that has a 12 V
battery. It is not compatible with a vehicle that has a 24 V battery.
≥ This is a special negative grounded Car DC Adaptor. Using this Car
DC Adaptor with a plus grounded car can cause malfunction and lead
to fire.
Car DC Adaptor
(included)
DC IN
Left side of this unit
Place the unit on a stable surface.
Replacing the fuse
Replace only with the specified 125 V/250 V, 2.5 A fuse. Use of any
other type can cause fire.
2
Replace the fuse (125 V/250 V, 2.5 A type)
Cautions
≥ To avoid draining your car battery
– Disconnect the Car DC Adaptor from the cigarette lighter after use.
The Car DC Adaptor continues to consume some power even if it is
not being used, and if a battery pack is attached to this unit, it will
start recharging which uses more power.
– Do not use the Car DC Adaptor for long periods when the engine is
not running.
≥ Turn the unit off before stopping the engine while using Car DC
Adaptor, otherwise resume play ( ➜ 6) may not work.
≥ Leave some slack in the cord.
≥ No responsibility will be taken for damage that occurs due to faulty
installation.
You can enjoy audio through your car audio
system by connecting a car stereo cassette
adaptor (not included) to the headphone jack
on the left side of this unit.
Left side of this unit
To the cigarette lighter
socket
3
Close
1
Open
FM transmitter
[DVD-LS86]
You can enjoy listening to discs through your FM radio channel (e.g. car
stereo) by transmitting audio signals from this unit.
≥ The FM transmitter can also be used with normal FM radio-equipped
devices.
Preparation
Unplug headphones from the unit.
≥ When connected, the FM transmitter will not work.
.
1
Play the disc. (➜ 6)
≥ When "AUX" or "iPod" is displayed, press [AV SELECT] to
select "DISC".
2 Press to display the menu.
FM TRANSMITTER
FM-TM
ON
STEREO
If the menu is not displayed, check the
"Preparation" steps listed above.
Press [3 4 2 1] to select "ON".
3
ENTER
The orange lamp lights up.
≥ No sound is heard from this unit.
4 Tune the radio to the 88.3 MHz FM frequency.
When another FM broadcast is heard
➜ see below, "When this has not been successful"
5 Adjust the volume using the radio.
≥ The volume control of this unit does not work while using the
FM transmitter.
To turn off the FM transmitter
Press [FM-TM] and then [ 3 4 2 1 ] to select "OFF".
To exit the screen
Press [FM-TM] .
When this has not been successful
1 Press to display the menu.
FM-TM
1 Press [3 4] to select the frequency
2
("88.3MHz") (factory preset).
2 Press [2 1] to select a frequency
between 88.3 MHz and 107.7 MHz which
ENTER
is not being used by any broadcasting
stations.
≥ The frequency can be set in 0.1 MHz
increments.
3 Tune the FM radio into the frequency selected in step
2.
If you experience noise or distortion of audio, move the radio antenna
closer to the unit. Or select "MONO" from the menu screen using
[ 3 4 2 1 ]. If the audio quality still does not improve, then change the
radio frequency ( ➜ above, "When this has not been successful").
Note
The FM transmitter only works during disc playback.
Turn the FM transmitter off while not playing discs, otherwise
background noise will be generated.
OFF
MONO
MHz
15
15