Herunterladen Inhalt Inhalt Diese Seite drucken

Vitek VT-7024 SR Betriebsanweisung Seite 4

Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 6
ENGLISH
Attention! Do not allow children to play with
polyethylene bags or packaging film. Danger of
suffocation!
Never pull the power cord when disconnect-
ing the unit from the mains, take the power
plug and carefully remove it from the mains
socket.
Never use the unit if the power cord or the
power plug is damaged, if the unit works
improperly or after it was dropped.
Do not disassemble the unit by yourself, if
any malfunction is detected or after it was
dropped, apply to the nearest authorized ser-
vice center.
Transport the unit in the original package only.
Keep the unit out of reach of children and dis-
abled persons.
THE UNIT IS INTENDED FOR HOUSEHOLD
USAGE ONLY
BEFORE THE FIRST USE
After unit transportation or storage at low
temperature, it is necessary to keep it for at
least two hours at room temperature before
switching on.
Unpack the kettle, remove any stickers that
can prevent unit operation. Make sure that the
operating voltage of the unit corresponds to
the voltage of your mains.
Insert the power plug into the mains socket.
To fill the kettle with water, take the kettle off
the base (8) and open the kettle lid (3) by
pressing the button (4).
Fill the kettle with water up to the maximal
mark on the water level scale (6), close the
lid and place the kettle on the base (8). Make
sure that the kettle lid (3) is closed tightly.
Switch the kettle on by setting the button (7)
to the position «I», the decorative illumination
of the water level scale (6) will light up.
Once water starts boiling, the kettle will be
switched off automatically, the decorative illu-
mination will go out. Pour out the water and
repeat the water boiling procedure 2–3 times.
Notes:
When using the kettle make sure that the lid
(3) is closed tightly, otherwise auto switch off
of kettle is not possible.
Before removing the kettle from the base,
make sure that the kettle is switched off,
that is, that the «0/I» button (7) is in the posi-
tion «0».
VT-7024.indd 4
USAGE
Note: There is a cord storage (9) on the reverse
side of the base (8). You can adjust the power
cord length by folding it in the cord storage in a
corresponding way.
Insert the power plug into the mains socket.
To fill the kettle with water, take it off the base (8)
and open the kettle lid (3) by pressing the button (4).
Fill the kettle with water, the water level must
not be below the minimal mark «min» or above
the maximal mark «max»; determine the water
level using the scale (6).
Close the lid (3), place the filled kettle on the
base (8).
Set the button (7) to the position «I», the dec-
orative illumination of the water level scale (6)
will light up.
Once water starts boiling, the kettle will be
switched off automatically.
You can switch the kettle off manually by set-
ting the button (7) to the position «0».
Before removing the kettle from the base (8),
make sure that it is switched off.
After the kettle is switched off, wait for 10-20
seconds, then you can switch it on again for
water re-boiling.
If you accidentally switch the kettle on with
insufficient amount of water, the automatic
thermal switch will be on and the kettle will be
switched off. In this case take the kettle from
the base (8), let it cool down for 5-10 minutes,
then fill it with water and switch it on, the kettle
will operate in normal mode.
Attention! To avoid scalding by hot steam,
do not bend over the kettle spout while it is
operating.
Filter cleaning
Before removing the filter (2), disconnect the
kettle from the mains, remove it from the base
(8), pour out water and let the kettle cool down.
Remove the filter (2) by pressing the upper
locks of the filter to delink them from the ket-
tle body.
Clean the filter (2) of the kettle from obstruc-
tion regularly; you can use a small brush for it.
Install the filter (2) back to its place, check
whether the filter (2) is installed properly.
CLEANING AND CARE
Before cleaning, disconnect the unit from the
mains, pour out water and let the kettle cool
down.
4
09.07.2014 15:09:42

Werbung

Inhaltsverzeichnis
loading

Inhaltsverzeichnis