Crown CT42019 Originalbetriebsanleitung Seite 27

Installation and regulation of appliance
elements
Before performing all the procedures, disconnect
the appliance from AC mains and water supply
system.
Do not draw up the fastening elements
too tight to avoid damaging the thread.
Mounting / dismounting / setting-up of
some elements is the same for all appli-
ance models, in this case specific mod-
els are not indicated in the illustration.
Installing / removing the rear holder (see fig. 1)
[CT42019, CT42020, CT42021, CT42022]
• Install rear holder 14 as shown in fig. 1. Tighten
screws 23�
• Disassembly operations do in reverse sequence�
Installing / removing the wheels (see fig. 2)
[CT42020, CT42021, CT42022]
• Install wheels 8 as shown in fig. 2.
• Disassembly operations do in reverse sequence�
Installing / removing the washer gun upper holder
(see fig. 3)
• Install upper holder 1 as shown in fig. 3.
• Disassembly operations do in reverse sequence�
Installing / removing the washer gun lower holder
(see fig. 4)
[CT42021, CT42022, CT42023, CT42024]
• Install lower holder 5 as shown in fig. 4. Tighten
screw 24�
• Disassembly operations do in reverse sequence�
Installing / removing the cable holder (see fig. 5)
[CT42019, CT42020, CT42021, CT42022]
• Install cable holder 7 as shown in fig. 5.
• Disassembly operations do in reverse sequence�
Installing / removing the handle (see fig. 6)
[CT42019, CT42020, CT42021, CT42022, CT42023]
• Install handle 10 as shown in fig. 6. Tighten
screws 25�
• Disassembly operations do in reverse sequence�
Installing / removing the pressure hose holder (see
fig. 7)
[CT42021, CT42023]
• Install holder 11 as shown in fig. 7. Tighten screws 26�
• Disassembly operations do in reverse sequence�
Installing / removing the reel (see fig. 8)
[CT42022]
• Install reel 21 as shown in fig� 8� Tighten
screws 27�
• Disassembly operations do in reverse sequence�
Installing / removing detergent tank (see fig. 9-10)
[CT42021, CT42022, CT42023, CT42024]
• Remove plug 13 (see fig. 9.1 and 10.1).
• CT42021, CT42022: remove tank 15 (see fig. 9.2).
• CT42023, CT42024: gently press on the sides of
tank 15 and remove the tank (see fig. 10.2).
• Perform all the necessary operations with tank 15:
emptying, cleaning, adding detergent, etc�)� While
pouring detergent into the tank, it is recommended to
use a funnel and wipe detergent drops and leakages
off tank 15 external surface with a cloth (see fig. 9.3
and 10�3)�
• Replace tank 15� CT42023, CT42024: gently press
on the sides of tank 15 to install it�
• Replace plug 13�
Installing / removing / adjusting spray gun (see
fig. 11-13)
[CT42019, CT42020]
• Insert extension tube 22 into spray gun 18 as shown
in fig. 11.2.
• Insert jet pipe 19 into extension tube 22�
• You can change stream pattern by rotating jet
pipe 19 tip (see fig. 11.1).
[CT42021, CT42022]
• Insert jet pipe 19 into spray gun 18 as shown in
fig. 12.3.
• You can change stream pattern by rotating jet
pipe 19 tip (see fig. 12.1).
• You can select low pressure or high pressure by
rotating jet pipe 19 nozzle coupling (see fig. 12.2).
Low-pressure mode is used for spraying detergent;
high-pressure mode, for high-pressure jet washing
without detergent�
[CT42023, CT42024]
• Insert jet pipe 19 into spray gun 18 as shown in
fig. 13.2.
• You can change stream pattern by rotating jet
pipe 19 tip (see fig. 13.1).
Installing / removing the filter (see fig. 14)
• Insert filter element 29 into filter housing 28 (see
fig� 14�1)�
• Screw filter 20 on inlet fitting 6�
• Follow the instructions above in reversed order to
remove the filter.
Water connection (see fig. 14)
• Always use filter 20 as the contaminants contained
in the water may damage the appliance�
English
27