Master BLP 11 Bedienungs- Und Wartungsanleitung Seite 12

► IMPORTANT:
maintenance and repairs that envision
access to dangerous parts (such as
replacement of a damaged power
supply cable) must be performed by
the manufacturer, by its technical after-
sales service, by a person with similar
qualification, in a way to prevent all
risks, even if disconnection from the
mains power supply is envisioned.
► IMPORTANT: Do not use the heater
if damaged. In case of any damage,
contact the after-sales assistance.
►2.1.For correct use of the heater and
for preservation of the fuel, follow all local
regulations and the Standard in force.
►2.2.The heater requires suitable fresh
air in order to function. It is therefore used
outdoors or in rooms with assured and
continuous supply of fresh air. Good airing
is supplied when the volume of the room is
calculated on the heat capacity, using the
formula of 1 m³ every 100 W of power. In
no case the recommended volume of the
room must be smaller than 100 m³. Good
ventilation is guaranteed by an opening
that satisfies the formula stating 25 cm²
per kW of heat power, with minimum of
250 cm², equally divided between the
upper and lower part of the room. National
Standards in force are valid for installation,
including the Technical Standards and the
provisions regarding accident-prevention
and the prevention of fires.
►2.3.The appliance must only be used
as a hot air heater (heating mode) or
fan (ventilation mode, for models that
envision this functionality). Follow these
instructions scrupulously.
►2.4.The
Manufacturer
liability for damage/injury to objects/
persons deriving from improper use of the
appliance.
►2.5.Only power the heater using the
type of fuel expressly specified and with
current having the voltage and frequency
All cleaning,
declines all
indicated on the data plate applied to the
heater.
►2.6.Make sure the heater is only
connected to suitable electric networks
with differential switch and suitable earth.
►2.7.Only use extensions with suitable
section, appropriately connected to earth.
►2.8.The heater must function on a stable
level and fire-proof surface, in a way to
prevent the risk of fire.
►2.9.It is prohibited to use the appliance
in basements and rooms below ground
level.
►2.10.The heater must not be used in
places where explosive dusts, fumes,
gases, fuels, solvents and paints are
present.
►2.11.Whenever the heater is used in
proximity of tarpaulin, awnings or similar
covering materials, it is considered to use
additional fire-proof protections. Make
sure the hot parts of the heater are kept
at a suitable distance from inflammable
materials (material, paper, wood, etc.)
or thermolabile materials (including the
power supply cable), which in no case is
less than 2,5 m.
►2.12.Position the gas cylinder in a
protected position, behind the appliance
(Pic. 1). The heater must never face the
gas cylinder (Pic. 2).
►2.13.The air vent (rear side) and/or the
air outlet vent (front side) cannot be totally
or partially obstructed for any reason (Pic.
3). Do not use any air ducting from or to
the heater. Make sure air intake slots,
present on the bottom of the base, are not
obstructed (for models using this solution).
►2.14.If the heater does not switch on or
switch-on is anomalous, consult the relative
section (Par. 13. "TROUBLESHOOTING").
►2.15.The heater must never be moved,
handled or subjected to any maintenance
interventions when it is running.
►2.16.In any condition of use or appliance
standstill, make sure that the flexible gas
en
it
de
es
fr
nl
pt
da
fi
no
sv
pl
ru
cs
hu
sl
tr
hr
lt
lv
et
ro
sk
bg
uk
bs
el
zh