Product Features; Product Description And Specifications - Bosch GWX Professional 10-125 Originalbetriebsanleitung

18 | English
If the use of a guard is recommended for wire brush-
u
ing, do not allow any interference of the wire wheel or
brush with the guard. Wire wheel or brush may expand
in diameter due to work load and centrifugal forces.
Additional safety information
Wear safety goggles.
Use suitable detectors to determine if utility lines are
u
hidden in the work area or call the local utility com-
pany for assistance. Contact with electric lines can lead
to fire and electric shock. Damaging a gas line can lead to
explosion. Penetrating a water line causes property dam-
age or may cause an electric shock.
Do not touch grinding and cutting discs until they have
u
cooled down. The discs can become very hot while work-
ing.
Release the On/Off switch and set it to the off position
u
when the power supply is interrupted, e. g., in case of
a power failure or when the mains plug is pulled. This
prevents uncontrolled restarting.
Secure the workpiece. A workpiece clamped with
u
clamping devices or in a vice is held more secure than by
hand.
Products sold in GB only:
Your product is fitted with an BS 1363/A approved electric
plug with internal fuse (ASTA approved to BS 1362).
If the plug is not suitable for your socket outlets, it should be
cut off and an appropriate plug fitted in its place by an au-
thorised customer service agent. The replacement plug
should have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains
socket elsewhere.
Product Description and
Specifications
Read all the safety and general instructions.
Failure to observe the safety and general in-
structions may result in electric shock, fire
and/or serious injury.
Technical Data
Angle grinder
Article number
Rated power input
Power output
Rated speed
Max. grinding disc diameter
Restart protection
Constant electronic control
1 609 92A 4FF | (22.01.2019)
Please observe the illustrations at the beginning of this oper-
ating manual.
Intended use
The power tool is intended for cutting, roughing and brush-
ing metal and stone materials without the use of water.
A special protective guard for cutting must be used when
cutting bonded abrasives.
Sufficient dust extraction must be provided when cutting
stone.
With approved abrasive tools, the power tool can be used for
sanding with sanding discs.

Product features

The numbering of the product features refers to the diagram
of the power tool on the graphics page.
(1) Unlocking lever for protective guard
(2) Direction of rotation arrow on housing
(3) Lever
(4) On/off switch
(5) Auxiliary handle (insulated gripping surface)
(6) Protective guard for grinding
(7) X-LOCK grinding disc/flap disc
(8) Protective guard for cutting
(9) X-LOCK cutting disc
(10) X-LOCK backing pad for fibre discs
A)
(11) X-LOCK fibre disc
(12) X-LOCK clip for fibre discs
A)
(13) Hand guard
(14) X-LOCK cup brush/disc brush
(15) X-LOCK holder
(16) Handle (insulated gripping surface)
(17) Extraction guard for cutting with a guide block
(18) Diamond cutting disc
(19) X-LOCK diamond core cutter
A) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.
GWX 10-125
3 601 GB3 0..
W 1000
W 630
-1
min 11,000
mm 125
A)
A)
A)
A)
A)
A)
A)
A)
A)
GWX 14-125
3 601 GB7 0..
1400
820
11,000
125
● ●
− ●
Bosch Power Tools