Limpieza Y Mantenimiento - Domo DO7293S Gebrauchsanleitung

· También puede elegir cargar el dispositivo antes de que se agote la batería pulsando el botón HOME
en el mando a distancia.
· Durante la carga:
· En la pantalla aparece el signo 1111 parpadeante: el aparato está cargándose.
· En la pantalla aparece "FULL": el aparato se ha cargado plenamente.
Product Maintenance
· En la pantalla aparece "Error": el interruptor de encendido/apagado debe estar encendido para la
Product Maintenance
carga.
Cleaning Side Brushes
duct Maintenance
Cargar sin la base de carga
Cleaning Side Brushes
Clean the side brush when it become dirty and replace it if it's damaged. The maximum life span of
Coja el adaptador, conecte el enchufe a la toma de corriente e introduzca la clavija DC en el aparato.
de Brushes
ning Side Brushes the side brush is 12 months.
· Durante la carga:
Clean the side brush when it become dirty and replace it if it's damaged. The maximum life span of
Note: Before replacing side brushes, check and ensure that the L/R mark on the side brush match
· En la pantalla aparece el signo 1111 parpadeante: el
the side brush is 12 months.
rush when it become dirty and replace it if it's damaged. The maximum life span of
he side brush when it become dirty and replace it if it's damaged. The maximum life span of
aparato está cargándose.
with the L/R mark on the bottom base of the robot.
Note: Before replacing side brushes, check and ensure that the L/R mark on the side brush match
12 months.
· En la pantalla aparece "FULL": el aparato se ha cargado
e brush is 12 months.
de Brushes
with the L/R mark on the bottom base of the robot.
Cleaning Dust Bin and Filters
plenamente.
lacing side brushes, check and ensure that the L/R mark on the side brush match
Before replacing side brushes, check and ensure that the L/R mark on the side brush match
Cleaning Dust Bin and Filters
rush when it become dirty and replace it if it's damaged. The maximum life span of · En la pantalla aparece "Error": el interruptor de
k on the bottom base of the robot.
e L/R mark on the bottom base of the robot.
Empty and clean the dust bin after each usage following the steps as show in the figures below:
encendido/apagado debe estar encendido para la
12 months.
Empty and clean the dust bin after each usage following the steps as show in the figures below:
st Bin and Filters
carga.
ning Dust Bin and Filters
lacing side brushes, check and ensure that the L/R mark on the side brush match
k on the bottom base of the robot.

LIMPIEZA Y MANTENIMIENTO

n the dust bin after each usage following the steps as show in the figures below:
and clean the dust bin after each usage following the steps as show in the figures below:
st Bin and Filters
LIMPIAR LA BANDEJA DE POLVO Y EL FILTRO
the dust bin after each usage following the steps as show in the figures below: Limpie la bandeja de polvo y el filtro después de cada uso, siguiendo los pasos a continuación:
1
A. Hold the bottom of dust bin, and press down on the button using your
A. Hold the bottom of dust bin, and press down on the button using your
thumb to take out of the dust bin.
thumb to take out of the dust bin.
m of dust bin, and press down on the button using your
d the bottom of dust bin, and press down on the button using your
ut of the dust bin.
to take out of the dust bin.
m of dust bin, and press down on the button using your
3
ut of the dust bin.
C. After press down button
C. After press down button
and o
pen dust bin upper cover
and o
pen dust bin upper cover
5
D. Open dust bin cover and take out the
down button
er press down button
primary filter and HEPA filter.
D. Open dust bin cover and take out the
n upper cover
en dust bin upper cover
down button
primary filter and HEPA filter.
upper cover
F. Wash the dust bin and primary filter under tap water,
F. Wash the dust bin and primary filter under tap water,
50
clean the HEPA filter with brush, avoid washing it under
clean the HEPA filter with brush, avoid washing it under
DO7293S
water.
water.
D. Open dust bin cover and take out the
D. Open dust bin cover and take out the
primary filter and HEPA filter.
primary filter and HEPA filter.
D. Open dust bin cover and take out the
primary filter and HEPA filter.
Battery Charging
1. Charging Station Placement
A. Place charging station against the wall,
and remove obstacles about 1m on either
sides and 2m in front of the station. Please
remove obstacles as show in the right figure.
B. If robot is power off, switch on the robot first before charging
Product Maintenance
Charge the robot in either way as shown below:
2.
Cleaning Side Brushes
A. Plug one end of the adapter into the robot and the other end
in Fig a.
Clean the side brush when it become dirty and replac
B. Press the "HOME" button on the remote control or robot to
the side brush is 12 months.
charging docking automatically as shown in Fig b.
Note: Before replacing side brushes, check and ensu
with the L/R mark on the bottom base of the robot.
Cleaning Dust Bin and Filters
Empty and clean the dust bin after each usage follow
Note:
a. When robot is in charging, the LED panel will gradually show
b. When charging is over, the LED panel will show "FULL".
A. Hold the bottom of dust bin, and press down on the bu
c. In standby status, the robot will
thumb to take out of the dust bin.
d. In working status, the robot will look for the charging dock au
2
level is low.
In Order to Extend Battery's Life
a. Please charge the robot for up to 5 hours during the first cha
b. Charge the robot as soon as possible when battery capacity
c. The robot will return to the charging dock automatically whe
B. Take out dust bin.
B. Take out dust bin.
capacity is low.
d. When you do not use the robot for some time, please fu
switch off the robot and keep it in a cool but dry place.
B. Take out dust bin.
4
C. After press down button
e. If the robot has been put aside over 3 months, please ch
before using it for cleaning.
and o
pen dust bin upper cover
6
E. Empty the dust bin.
E. Empty the dust bin.
F. Wash the dust bin and primary filter under tap water,
E. Empty the dust bin. clean the HEPA filter with brush, avoid washing it under
water.
G. Assemble primary filter and HEPA filter again into
G. Assemble primary filter and HEPA filter again into
dust bin.
dust bin.
Fig a
show
B. Take out dust bin.
B. Take out dust bin.
D. Open dust bin cover
primary filter and HEPA
E. Empty the dust bin.
E. Empty the dust bin.
when the batt
10
G.
du
16