Instructions For Use; Important Safeguards; Park Position; Replacing The Dust Bag - Nilfisk GO Bedienungsanleitung

DJ68-00249A(0.3)-1215-1
ENGLISH

INSTRUCTIONS FOR USE

FEATURES
Features include automatic cord rewind and dust indicator.
NOTE: Not all models have the same features.

IMPORTANT SAFEGUARDS

1. Read all instructions carefully. Before switching
on,make sure that the voltage of your electricity sup-
ply is the same as that indicated on the rating plate
on the bottom of the cleaner.
2. WARNING: Do not use the vacuum cleaner when
rug or floor is wet.
3. Close supervision is necessary when any appliance
is used by or near children. Do not allow the vacuum
cleaner to be used as a toy. Do not allow the vacu-
um cleaner to run unattended at any time. Use the
vacuum cleaner only for its intended use as
described in these instructions.
4. Do not use the vacuum cleaner without a dust bag.
Change the dust bag before it is full in order to main-
tain best efficiency.
5. Do not use the vacuum cleaner to pick up matches,
live ashes or cigarette butts. Keep the vacuum
cleaner away from stoves and other heat sources.
Heat can deform and discolor the plastic parts of the
unit.
6. Avoid picking up hard, sharp objects with the vacu-
um cleaner as they may damage the cleaner parts.
Do not stand on the hose assembly. Do not put a
weight on the hose. Do not block the suction or the
exhaustion part.
7. Switch the vacuum cleaner off at the machine before
unplugging from the electrical outlet. Grasp the plug
to disconnect from power outlet to avoid damage to
cord, plug, prongs or socket. Do not pull the power
cord. Always disconnect cord from electrical outlet
before changing the dust bag.
8. The use of an extension cord is not recommended.
9. If your vacuum cleaner is not operating correctly,
switch off the power supply and consult an autho-
rized service agent.
10.Do not attempt to replace a damaged power supply
cord. Only the manufacturer or qualified service per-
sonnel can replace power cords. Serious injury may
result.
WARNING
1. Do not use to suck up water.
2. Do not immerse in water for cleaning.
3. The hose should be checked regularly and must not
be used if damaged
1. IDENTIFICATIONS OF PARTS
HANDLE
AIR REGULATOR
TUBE
FLOOR NOZZLE
RUG/FLOOR SELECTOR
12/15/04 12:02 PM Page 6
2. ASSEMBLING THE VACUUM-CLEANER READY FOR
USE
1) Connect the suction hose to the suction tube.
2) Connect the nozzle to the suction tube.
3) Grip the body connector with one hand and squeeze
3. USING THE ACCESSORIES
4. POWER CORD
1) PULLING OUT
The power cord is long enough to be drawn out for
convenience.
2) REWINDING
When you have finished cleaning, disconnect the plug
from the electrical outlet and simply press the cord
rewind button lightly with your toe.
NOTE : When removing the power cord from the elec-
5. ON/OFF SWITCH
With the cord plugged into an electrical outlet, start or
stop the vacuum cleaner by pushing lightly downward
on the switch.

6. PARK POSITION

Located on the top rear side of the vacuum-cleaner,
there is a nozzle support that can be used to park the
nozzle during pauses in cleaning.
7. TRANSPORTING AND STORING THE VACUUM
CLEANER
For easy storage and transportation, this vacuum cleaner
has a clip system built onto the body, which will keep the
tube, hose and nozzle in a vertical position.

8. REPLACING THE DUST BAG

If the "Dust-Full" indicator changes to "RED" while you
are cleaning, the dust bag requires replacement.
NOTE : If the "Dust-Full" indicator continues to display
1) To open the dust cover of the dust bag compart-
2) Remove the dust bag from the cleaner.
3) After removing the used dust bag, insert the card-
4) Press the dust cover down gently until the clamper
4
SUCTION HOSE
DUST-FULL INDICATOR
BUTTON
TOOL STORAGE COVER
CLAMPER FOR DUST BAG COMPARTMENT
the tube in an inward direction.
DUSTING BRUSH
UPHOLSTERY
trical outlet, grasp the plug, not the cord.
"RED" even after changing the dust bag, turn
the cleaner off and check whether the hose,
tube or nozzle is clogged.
ment, press the clamper upwards.(The clam-
per is located at the front of the dust cover)
board bag collar of the new dust bag into its original
position.
relocks.