Lcd-Display - JBSystems mcd 580 Bedienungsanleitung

ENGLISH
the original pitch when the button is released. These buttons can be used to synchronize the beats of 2
tracks.
7. PITCH button: This button is used to turn the Pitch function on and off. If you want to change the speed
adjustment range (+/- 8%, +/- 12% , +/- 16%), press and hold PITCH button then press the PITCH
BEND+ to select.
8. PITCH slider: Press the PITCH button, the PITCH LED is on. The speed can be changed up to +/-16%
by moving the sliding fader. The speed will not change if the PITCH LED is off.
9. OPEN/CLOSE button: press this button to open and close the disc tray in the front of the main unit.
This button is disabled during playback. If the tray is not closed after 60sec. It will close automatically to
prevent mechanical damage.
10. TIME Button: The TIME button switches between elapsed playing time, remaining time in a selection
and total remaining time of the disc. (standard = remaining /track)
11. SGL/CTN Button: with this button you can choose between "single track mode" and "continuous play".

Continuous play: the complete CD will be played without interruption. (mostly used in pubs)

Single track: player stops at the end of each track and waits at the beginning of the next track. The
player will wait at the first music note of each track.
12. PROGRAM Button: It is possible to program up to 20 tracks on each deck. After programming the
tracks will be played in the order you programmed. You can also use the relay function to make a
preprogrammed sequence on the 2 decks. Follow the steps below for programming:
 Press the PROGRAM button once, the led next to it turns on and the display shows "-- P-01 00".
 Choose the first track in your sequence and press the PROGRAM button. The first track is
programmed, the display shows "-- P-02 01"
 Choose the second track in your sequence and press the PROGRAM button. The second track is
programmed, the display shows "-- P-03 02"
 Continue these steps until you are finished.
 Now simply press the "play/pause button" to start the sequence. The first track in your sequence
starts playing while the display shows"** P-01"
The programmed sequence plays in an endless loop until you stop the program mode by pressing the
PROGRAM button for about 2 seconds". The led next to the PROGRAM button turns off and the
program memory is cleared.
13. LCD DISPLAY: Shows all important information needed during playback. Refer to the next chapter for
more information.
14. LOOP Button: Used to make the music play in a loop, follow the steps below to create a loop:
 Make sure that the track is playing.
 Press the LOOP button to set the beginning of the loop: led starts flashing.
 Press the LOOP button again to set the end of the loop: led is lit while the music starts playing in
loop mode.
 Press the LOOP button again to stop the loop mode: the led turns off.
15. FADERSTART sockets: If you are using a mixer with fader start function, use the supplied mono mini
jack/jack cable to connect the player with the fader start of the mixer. Please note that this socket must
never be connected with any voltage.
Attention: This remote control is only compatible with (Synq® or Pioneer® compatible) mixers.
16. CONTROL connector: Connect the main unit here, using the supplied mini-DIN8 cable.
JB SYSTEMS®
USER MANUAL
5/47 MCD580
ENGLISH
LCD DISPLAY
1. TRACK: Shows current track number.
2. TIME BAR: shows either time remaining or elapsed depending on the setting of the TIME button. Starts
flashing at the end of each track to alert the user to take action.
3. MINUTE: Shows "minutes" time information of current track.
4. SECOND: Shows "seconds" time information of current track.
5. FRAME: Shows "frame" time information of current track. (1 frame = 1/75
6. SINGLE/CONTINUE: "single" appears when the unit is set to play just one track at a time. Otherwise the
CD will play continuously through all tracks. This function is controlled by the SGL/CTN button.
7. ELAPSED, TOTAL REMAIN: indicates that the time shown on the display is the track elapsed,
remaining or total remaining time.
8. PITCH DISPLAY: Shows the percentage change in pitch (speed) of the song.
HOW TO USE ...
Most of the common functions are explained in the previous chapter "controls and functions" In this chapter
we talk about the functions that need a little more explanation.
 PLAYING MP3 FILES:
The CD player automatically detects if a CD contains MP3 files. The MCD580 is able to read several
different MP3 formats but due to display limitations it can't show the ID3-tags (song title/performer/...). The
CD may contain up to 999 MP3- files, spread over maximum 255 folders. When the MP3-files are sorted in
separate folders, the MCD580 will list all files as if no folders exist.
The MP3-files may have the following file extensions: .mp3 ~ .MP3 ~ .mP3 ~ .Mp3
Check the technical specifications to see which MP3-files are allowed.
 PLAYING CD-R and CD-RW:
Apart from normal audio CD's the MCD580 can play both CD-R (CD recordable) and CD-RW (CD
rewriteable). Please note that you should always use the "disc at once" and "track at once" disc writing
options! If the disc is multi session, it will only play the first session:
if the first session is CD-DA you can only play CD-DA tracks.
o
if the first session is MP3 you can only play MP3 files.
o
 SLEEP MODE:
The CD player automatically shuts off the transport and laser after about 15 minutes (when in pause or
cue mode). This extends the life of your motor drive and laser. During sleep mode the display shows the
word "SLEEP". To wake up the player, just press the cue or play button, the display turns to normal and is
ready to receive instructions.
 RELAY FUNCTION:
Relay play allows consecutive playback for two decks, perfect for pubs etc.
 Put a disc in both players.
 Open the 2 channel faders of the corresponding CD inputs on your mixer.
 Press one of the PROGRAM buttons and hold it down, now press the SGL button on its left to enable the
Relay function. Both the players will be set to single mode and the track numbers on both displays start
flashing.
JB SYSTEMS®
USER MANUAL
th
sec.)
6/47 MCD580