Inhaltsverzeichnis
Werbung
6 . 1 2
S P E C I F I C I N S T R U C T I O N S F O R
U S E O F M O D E L
A C 23 0 V
The AC 230V model machine may be turned on
only if the voltage indicated on the tag corresponds
w ith the available voltage and that the electrical
outlet is grounded (earthed).
Do not damage the feed cable; do not crush or
pull on it.
Do not run over the feed cable w ith the machine.
The cable could w ind up in moving parts causing
a short circuit.
A T T E N T I O N
! ! ! - T h e m o d e l A C 23 0 V m a -
c h i n e
h a s
p a r t s , w h i c h
t h e c u r r e n t ; c o n t a c t w i t h t h e s e c o u l d c a u s e
g r a v e i n j u r i e s o r e v e n d e a t h .
- Before ex ecuting any type of operation on the
machine alw ays disconnect it from the electrical
source.
- Never touch electric cables that are defective or
w orn.
- Before gaining access to the electrical system it is
alw ays necessary to disconnect the machine from
the electrical source.
- In the case of defective, damaged, or cracked
electric cables, replace immediately w ith authentic
replacement parts.
- The netw ork of connections must be protected
from w ater spray.
- The patch cord for the connection of the machine
to the mains pow er must conforms to current sa-
fety rules.
- The electrical system to w hich the machine is
connected must be equipped w ith a cutout box .
- It is absolutely forbidden to use the machine in
prox imity to sw imming pools or stretches of w ater.
E M E R G E N C Y S I T U A T I O N S
I n c a s e o f e m e r g e n c y :
- I m m e d i a t e l y d i s c o n n e c t t h e m a c h i n e f r o m
t h e p o w e r m a i n s .
- I m m e d i a t e l y a p p l y p r o p e r f i r s t - a i d .
If an accident should occur the machine must not
be put into operation until a technician authorized
by the manufacturer has ex amined it.
6 . 1 3
D R I V I N G T H E M A C H I N E
M o d e l A C 23 0 V
- Connect the pow er cable of the machine ( Photo
B - 1) to the pow er mains using a patch cord.
- Sw itch ON the general ON-OFF sw itch ( Photo
A - 1).
- Sw itch ON the brush motor sw itch ( Photo A - 2).
T h e b r u s h w i l l s t a r t t h e r o t a t i o n o n l y w h e n
t h e m a c h i n e o p e r a t o r w i l l o p e r a t e t h e b r u s h
o p e r a t i o n l e v e r ( P h o t o B - 4 ) .
- Sw itch ON the suction motor sw itch ( Photo A
- 3).
T H E
a r e
c o n n e c t e d
t o
36
- Low er the squeegee unit by using the lift/low er
lever ( Photo B - 3)
- Low er the brush plate unit by using the lift/low er
lever ( Photo B - 2)
- Wash the floor moving forw ard slow ly, pulling the
brush operation lever ( Photo B - 4); releasing the
lever the brush rotation w ill stop after few seconds.
Remember to lift the squeegee before driving
reverse to avoid damaging it.
M o d e l D C 24 V
- Verify that the battery connector placed in the
back of the machine ( Photo D - 7) is connected.
- Put the ignition key ( Photo D - 1) in and turn ON
the machine.
- In the control panel, check the battery charge
status ( Photo C - 3 )
- Sw itch ON the brush motor sw itch ( Photo C - 1).
( ! ) The brush w ill start the rotation only w hen the
machine operator w ill operate the brush operation
lever ( Photo D - 2).
- Sw itch ON the suction motor sw itch ( Photo C
- 2).
- Low er the squeegee unit by using the lift/low er
lever ( Photo D - 4)
- Low er the brush plate unit by using the lift/low er
lever ( Photo D - 3)
- Wash the floor moving forw ard slow ly, pulling the
brush operation lever ( Photo D - 2); releasing the
lever the brush rotation w ill stop after few seconds.
Remember to lift the squeegee before driving
reverse to avoid damaging it.
M o d e l D C 24 V w i t h t r a c t i o n
- Verify that the battery connector placed in the
back of the machine ( Photo F - 8) is connected.
- Put the ignition key ( Photo F - 1) in and turn ON
the machine.
- In the control panel, check the battery charge
status ( Photo E - 1 ) and, if sufficient, select the
running speed w ished ( Photo E - 3, E - 4 ).
- Sw itch ON the brush motor sw itch ( Photo E - 5).
T h e b r u s h w i l l s t a r t t h e r o t a t i o n o n l y w h e n
t h e m a c h i n e o p e r a t o r w i l l o p e r a t e t h e b r u s h
o p e r a t i o n l e v e r ( P h o t o F - 2) .
- Sw itch ON the suction motor sw itch ( Photo E
- 6).
- Low er the squeegee unit by using the lift/low er
lever ( Photo F - 4)
- Low er the brush plate unit by using the lift/low er
lever ( Photo F - 3)
- Wash the floor moving forw ard by pulling the
traction lever ( Photo F - 2) up or push the traction
lever dow n to reverse traction; releasing the lever
the traction w ill stop immediately and brush rota-
tion w ill stop after few
Remember to lift the squeegee before driving
reverse to avoid damaging it.
seconds.
Werbung
Kapitel
Inhaltsverzeichnis
