Conrad 75 19 01 Bedienungsanleitung Seite 4

Programming a receiver
The motion detector has a sliding switch with which the pro-
gramming code can be selected. Remove the front plate of the
motion detector to be able to access the sliding switch.
An individual code can be selected with this slider switch via the
positions IV-1, IV-2, IV-3. Motion detector and receiver are pro-
grammed according to this code. You thus avoid interference of
other radio devices that work with the same frequency.
Select the switch position „Learning Code" so that the motion
detector automatically allocates an individual code.
In any case, also observe the operating instructions of the
receiver which is to be programmed.
The programming procedure can be slightly different for different receivers. The receiver mostly
has a button which must be kept pressed until a red LED starts to flash. While this LED flashes,
the receiver must be activated once. Then, the motion detector emits a radio signal to the
receiver. The LED at the receiver is deactivated and the programming process is complete.
Limiting the motion detection range
The movement detection range can be limited with the diffuser lens included in the delivery. The
cover can be fitted e.g. with scissors. Then the diffuser lens cover is attached to the diffuser lens.
Maintenance and care
The product does not require any maintenance and should never be opened or disassembled
for any reason.
Clean the product with a soft, clean and dry cloth. Never use aggressive cleaning agents or che-
mical solutions since these might damage the surface of the casing or impair the operation.
Handling
• The wireless motion detector must not get damp or wet.
• Avoid the following unfavourable environmental conditions in the during use and
during transportation:
- Humidity and dampness may cause damage to the motion detector.
- Direct sunlight
- Extreme cold or heat
- Dust or flammable gases, fumes or solvents
- Strong vibrations
- Strong magnetic fields such as those found in the vicinity of machinery or loud-
speakers
• Ensure that the enclosure of the entire product is neither damaged nor destroyed.
Never disassemble the product! Except for changing the battery, there are no
serviceable parts inside.
• Check the product for damage before use!
If you notice any damage, do not use the product any longer!
Safe operation must be presumed to be no longer possible:
- if the device is visibly damaged
- if the device no longer works
- if the device was stored under unfavourable conditions for a long period of time
- the device was exposed to extraordinary stress caused by transport.
Transmission range
The transmission range of the radio signals between the wireless motion detector and the cor-
responding receiver is up to 70m under optimum conditions.
This value, however, is the so-called „open space range" (the range the trans-
mitter and receiver are visible to each other, without interfering influences).
In practical operation, however, there are walls, ceilings of rooms etc. between
the transmitter and the receiver, which reduce the range accordingly.
Due to the different influences on the radio transmission, no specific range can
be guaranteed.
However, trouble-free operation is usually possible in a detached house.
The coverage can partly be limited considerably by:
Sliding switch for selection of
• walls, reinforced concrete ceilings
learning code:
• coated/metallised insulated glass
• proximity to metal & conducting objects (e.g. radiators)
• proximity to human bodies
• Broadband interferences, e.g. in residential areas (DECT telephones, mobile phones, radio-
controlled headphones, radio-controlled speakers, radio-controlled weather stations, baby
phones etc.)
• Proximity to electric motors, transformers, power-supply units, computers
• The proximity to improperly shielded or uncovered operating computers or other electric
appliances
Disposal
a) General
b) Batteries and rechargeable batteries
As the end user, you are required by law (Battery Ordinance) to return all used batteries/rechar-
geable batteries; disposal of them in the household waste is prohibited!
Declaration of conformity
We, Conrad Electronic, Klaus-Conrad-Straße 1, D-92240 Hirschau, hereby declare that the
product conforms to the fundamental requirements and the other relevant regulations of
Directive 1999/5/EC.
Technical data
Transmission frequency:
Power supply:
Range:
Motion detection angle
Horizontal:
Detection range:
Operating temperature:
Weight without batteries:
Dimensions (L x W x H):
© Copyright 2010 by Conrad Electronic SE.
Electrical and electronic products do not belong in the household waste!
Please dispose of the device when it is no longer of use, according to the current
statutory requirements.
Contaminated batteries/rechargeable batteries are labelled with these symbols to
indicate that disposal in the domestic waste is forbidden. The designations for the
heavy metals involved are: Cd = Cadmium, Hg = Mercury, Pb = Lead.
You can return used batteries/rechargeable batteries and button cells free of charge
to any authorised disposal station in your area, to our stores or to any other store
where batteries/storage batteries/button cells are sold.
Thus you fulfil the legal requirements and contribute to protecting the environment!
The Declaration of Conformity for this product can be found at www.conrad.com.
433MHz
2 x 1.5V micro batteries (type: AA).
up to 30 metres (open space, see chapter „Transmission
range")
90°
up to 8 metres
0° to +35°C
approx. 56 grams
approx. 80 x 80 x 28 mm
These operating instructions are a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240
Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or
the capture in electronic data processing systems require the prior written approval by the editor.
Reprinting, also in part, is prohibited.
These operating instructions represent the technical status at the time of printing. Changes in
technology and equipment reserved.