Trevi RC 845 B Bedienungsanleitung Seite 5

RC 845 B
CONFIGURATION ANDFUNCTIONS :
1. Sleep Button
2. Volume Down/Alarm Button
3. Volume Up Button
4. Time Set Button
5. Preset/Memory Up
6. Tuning Down/Hour Button
7. Tuning Up/Minute Button
8. On/Standby/Alarm Off
Button
9. Built-In Speaker
(Back side)
10. Snooze Button
11. Battery Compartment
(Back side -
Backup batteries)
12. Alarm Indicator -
Buzzer / Radio
13. LED Display
14. Sleep Indicator
CONNECTING THE UNIT
Insert the wired plug correctly into a power outlet. The clock display will show "00 : 0 0" and you
need to set the correct time. It will also return to show "00 : 0 0" if there has been a power out
and no back-up battery is fitted.
TO SET THE TIME
Set the unit to Standby mode. You can only set the time when unit is in Standby mode.
1. Press and hold the Time Set Button for about 2 seconds. Then the current time will be
flashing. Release the button.
. 2 Press the Hour Button once and repeatly to adjust the hour digit
. 3 Press the Minute Button once and repeatly to adjust the minute digit
Note: Press and hold the Hour/Minute Button will change the digit at a fast speed.
4. Press once again the Time Set Button when it reaches the right time. Then the
current time will stop flashing.
RADIO OPERATION
1. Press the On/Standby Button to set the unit to Radio mode.
2. Tune a station by pressing the Tuning Up/Down Button.
Pressing either Tuning Up/Down Button for more than 1 second to activate the
automatic tuning mode. The automatic tuner will scan up or down and lock onto the next
station. If the automatic tuning does not precisely tune into a radio station, press the
Tuning Up/Down Button to adjust the tuning.
3. Adjust the volume by pressing Volume Up/Down Button.
4. To turn off the radio, press the On/Standby Button to set the unit to Standby mode.
5. After tuned into a radio station, the unit will return to show the current time instead of
the radio frequency after a few seconds.
6. If you want to check the radio frequency, press either once the Tuning Up or Tuning
Down button then the unit will show the radio frequency for a few seconds.
p65 3
STORES PRESET STATIONS
Up to 10 stations can be stored in memory :
1. Tune to a desired station as described in previous section.
2. Press and hold the Preset/Memory Up Button for about 2 seconds then the Preset Station
Number will flash. Release the button.
3. Press once or more times the Volume Up/Down Button to select your desired Preset
Station Number from P1 to P10.
4. Press once the Preset/Memory Up Button then the Preset Station Number will stop
flashing. Now the station is stored in your desired Preset Station Number.
To replace a station stored in the memory, repeat all the stages described above. The new
station will replace the previously stored one.
To receive Preset Stations :
1. Press once or more times the Preset/Memory Up Button to select the desired
Preset Station Number.
TO SET THE ALARM TIME AND THE ALARM MODE
Set the unit to Standby mode. You can only set the alarm time when unit is in Standby mode.
. 1 Press and hold the the Alarm Button for 2 seconds Then the alarm time will be flashing
Release the button.
. 2 Press the Hour Button once and repeatly to adjust the hour digit
. 3 Press the Minute Button once and repeatly to adjust the minute digit
Note: Press and hold the Hour/Minute Button will change the digit at a fast speed.
4. Press once again the Alarm Button when it reaches the right time. Then the alarm time
will stop flashing. The alarm time is set.
. 5 Press once or more times the Alarm button to select which type of alarm you like as below
:-
a) Alarm - Indicator light on : Buzzer selected as alarm type.
b) Alarm - Indicator light on : Radio selected as alarm type.
c) Alarm - &
the unit will not alarm when it reaches the Alarm set time.
p65 4
AM/FM ALARM CLOCK
1 2 3 4 5 6
9
10
12 13
.
.
.
.
Indicators both light off : No alarm selected, meaning that
USE THE ALARM
1 . Set the Alarm time and select alarm type as described in previous section . Make sure the
7 8
Alarm indicator is on.
. 2 When it reach the alarm time, you can hear the radio or buzzer sound depending on
which alarm type you have selected before.
. 3 Press once the Alarm Off Button to turn off the alarm sound then the radio or buzzer
sound will be off.
Note : If you select FM Radio as alarm type, make sure you have turned a desired station
and a suitable volume level before using this alarm type.
11
SNOOZE OPERATION
To obtain approximatively further 9 minutes sleep, press the Snooze Button after the radio or
the buzzer switch on at the preset wake-up time. The Alarm Indicator will be flashing. This will
silence the radio or the buzzer for 9 minutes. You can repeat this operation for up to about 1
hour.
GOING TO SLEEP WITH THE SOUND OF THE RADIO
1. Press once the Sleep Button to activate the Sleep function. The Sleep Indicator will on.
. 2 Press once and repeatly the Sleep Button to select the sleeping time (minutes) as
90-80-70-60-50-40-30-20-10 -OFF (OFF meaning that Sleep function is cancelled).
After setting the sleeping time, the radio will on and off and return to standby mode when it
14
reached the sleep set time.
If you want to cancel the sleep funciton, simply press once the On/Standby Button then the
sleep function will be disable. The Sleep Indicator will off and the unit will return to Standby
mode.
GOING TO SLEEP AND WAKENING TO THE SOUND OF THE UNIT
. 1 Repeat steps described in "TO SET THE ALARM TIME AND THE ALARM MODE"
and "USE THE ALARM".
. 2 Press the Sleep Button and set the period of time you want to listen to the radio
before it switches off automatically.
. 3 The radio is now programmed to turn itself off after you go to sleep and the alarm will
on automatically at the preset wake-up time.
BATTERY BACK-UP
This clock radio has a back-up power system to ensure continuous operation of the clock in the
event of a power failure. The switch from AC to battery power is automatic. However, under
battery power, the clock display will not illuminate even though the clock maintains the correct
time and stores the alarm time in the memory. The system operates on 2x1.5V "AAA" size
batteries (not included). We recommend the use of a long life battery to ensure maximum
performance.
CHECKING THE TIME DURING NO SUPPLY OF AC POWER (WITH BACKUP
BATTERIES)
When there is no supply of AC power but the unit is fitted with 2x1.5V "AAA" size batteries (for
backup), the display will not show any information. However, you can still check the current time
by pressing any button and the current tme will be displaying for a few seconds. But, It will not
alarm when it reaches the preset alarm time.
ANTENNA
The unit has a flexible wire on the back of the unit and it should be extended to its full length
for best reception white receiving FM radio.
E18 (Single).p65 SPECIFICATIONS
2014/6/17, 下午 05:13
Power Source
Frequency Range
Dimensions
Weight
Weight and dimensions are approximate because we continually strive to improve our products,
specifications may change without prior notice.
.
E18 (Single).p65
2014/6/17, 下午 05:13
5
: AC230V ~ 50Hz
DC3V , 2x1.5V "AAA" size batteries type (for clock
back-up) (battery not included)
: FM 87.5-108 MHz
: 155(L) x 73(D) x 84(H) MM
: 310g
6
ENGLISH
2014/6/17, 下午 05:13
2014/6/17, 下午 05:13
5