Operation; Switch Lock - Status Ctr20Li Originalbetriebsanleitung

6. OPERATION

OPERATION
ON/OFF SWITCH (Fig.D)
Depress to start and release to stop your drill.
The ON/OFF switch (Fig.A Pos.5) is fitted with a brake function which stops
your chuck immediately when you quickly release the switch.
It is also a variable speed switch than delivers higher speed and torque
with increased trigger pressure.
Speed is controlled by the amount of switch trigger depression.
WARNING! Do not operate for long periods at low speed because excess
heat will be produced internally.

SWITCH LOCK

The ON/OFF switch trigger can be locked in OFF position.
This helps to reduce the possibility of accidental starting when not in use.
To lock the switch, place the forward and reverse rotation selector (Fig.A
Pos.6) in the center position by pushing it on either side of the drill.
REVERSIBLE
The forward/reverse rotation control located above the ON/OFF switch
controls direction of rotation (Fig.A Pos.6)
For drilling and screw driving use forward rotation marked "
(lever is moved to the left).
Only use reverse rotation marked "
to remove screws or release a jammed drill bit.
When the selector is in the center position, the switch is locked.
CHUCK ADJUSTMENT (Fig.E)
To open the chuck jaws rotate the front section of the chuck. Insert the drill bit
between the chuck jaws and rotate the front section in the opposite direction.
Ensure the drill bit is in the center of the chuck jaws. Finally, firmly rotate the front
chuck section in the opposite directions. Your drill bit is now clamped in the chuck.
TORQUE ADJUSTMENT (Fig.F)
Screw driving force of your drill driver.
The torque is adjusted by rotating the torque adjustment ring (Fig.A Pos.2).
The torque is greater when the torque adjustment ring is set on a higher setting.
The torque is less when the torque adjustment ring is set on a lower setting.
1 - 5 For driving small screws
6 - 10 For driving screws into soft material
11 - 15 For driving screws into soft and hard material
16 - 20 For driving screws into hard wood
21 - 25 For driving larger screws
For heavy drilling
EN
"
" (lever is moved to the right)
8
SPEED CHANGE (Fig.A Pos.3)
• Always set the speed change lever fully to the correct position. If you operate the
tool with the speed change lever positioned halfway between the
side, the tool may be damaged.
• Do not use the speed change lever while the tool is running. The tool may be
damaged. To change the speed, first switch off the tool and then slide the speed
change lever to the side for high speed or
the speed change lever is set to the correct position before operation.
USING THE SIGHT LIGHT (Fig.A Pos.4)
The sight light allows you to keep a clear view under less illuminated circumstances.
To turn on the light simply press the ON/OFF switch. When you release the ON/OFF
switch, the light will be off.
DRILLING
When drilling into a hard smooth surface, use a center punch to mark the desired
hole location. This will prevent the drill bit from slipping off center as the hole is
started. Hold the tool firmly and place the tip of the bit at the point to be drilled.
Depress the switch trigger to start the tool. Move the drill bit into the workpiece,
applying only enough pressure to keep the bit cutting.
Do not force or apply side pressure to elongate a hole.
Note: If your tool stops working when drilling a hole automatically, it's
normal. This is the electrical protection for battery. Completely release the
ON/OFF switch, then depress it to start the tool again.
DISPOSAL OF AN EXHAUSTED BATTERY PACK
To preserve natural resources, please recycle or dispose of the battery pack
properly. This battery pack contains lithium batteries. Consult your local waste
authority for information regarding available recycling and/or disposal options.
Discharge your battery pack by operating your drill, then remove the battery pack
from the drill housing and cover the battery pack connections with heavy duty
adhesive tape to prevent short circuit and energy discharge. Do not attempt to
open or remove any of the components.
Why does the drill not turn on when your press the switch?
The forward/reverse rotation control, which is on top of the trigger, is positioned in
the lock function. Unlock the forward/reverse rotation control by putting it into the
required rotation position. Push the trigger and the drill will start to rotate.
The drill stops before the screw is completely tightened, why?
Verify the torque position of the variable clutch, you can find the variable clutch
between the chuck and the drill body. Positions 1 is the lowest torque (screw
driving force) and position 25 is the highest torque (screw driving force).
Position is for drill operation. Regulate the variable clutch to a higher
position to reach the best result.
I cannot fit the battery into the battery charger, why?
The battery can be inserted into the charger only in one direction.
side and
side for low speed. Be sure that
9