Battery Charge Indicator; Dust/Chip Extraction; Starting Operation - Bosch GSR 14,4-2-LI Plus Professional Originalbetriebsanleitung

Do not continue to press the On/Off switch after the
u
power tool has automatically switched off. The battery
can be damaged.
Follow the instructions on correct disposal.
Removing the Battery
The battery (7) is equipped with two locking levels to pre-
vent the battery from falling out when pushing the battery re-
lease button (8) unintentionally. As long as the battery is in-
serted in the power tool, it is held in position by means of a
spring.
To remove the battery (7), press the release button (8) and
pull the battery out of the power tool. Do not use force to
do this.

Battery charge indicator

The green LEDs on the battery charge indicator indicate the
state of charge of the battery. For safety reasons, it is only
possible to check the state of charge when the power tool is
not in operation.
Press the button for the battery charge indicator or
show the state of charge. This is also possible when the bat-
tery is removed.
If no LED lights up after pressing the button for the battery
charge indicator, then the battery is defective and must be
replaced.
Battery model GBA 18V...
LEDs
3× continuous green light
2× continuous green light
1× continuous green light
1× flashing green light
Battery model ProCORE18V...
LEDs
5× continuous green light
4× continuous green light
3× continuous green light
2× continuous green light
1× continuous green light
1× flashing green light
Changing the Tool (see figure B)
Remove the battery from the power tool before carry-
u
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
Bosch Power Tools
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
The drill spindle is locked when the on/off switch (11) is not
pressed. This makes it possible to change the application
tool in the drill chuck quickly, conveniently and easily.
Open the keyless chuck (2) by turning it in the direction of
rotation ➊ until the tool can be inserted. Insert the tool.
Firmly tighten the keyless chuck (2) by turning it by hand in
the direction of rotation ➋. This will automatically lock the
drill chuck.

Dust/Chip Extraction

Dust from materials such as lead-containing coatings, some
wood types, minerals and metal can be harmful to one's
health. Touching or breathing-in the dust can cause allergic
reactions and/or lead to respiratory infections of the user or
bystanders.
Certain dust, such as oak or beech dust, is considered carci-
nogenic, especially in connection with wood-treatment ad-
ditives (chromate, wood preservative). Materials containing
to
asbestos may only be worked by specialists.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the ma-
terials to be worked.
Avoid dust accumulation at the workplace. Dust can
u
easily ignite.
Operation
Capacity

Starting Operation

60−100 %
Inserting the battery
30−60 %
Note: The use of batteries unsuitable for your power tool can
5−30 %
lead to malfunctions or damage to the power tool.
0−5 %
Push the charged battery (7) into the base of the power tool
until the battery is securely locked.
Setting the rotational direction (see figure C)
The rotational direction switch (10) is used to change the ro-
tational direction of the power tool. However, this is not pos-
sible while the on/off switch (11) is being pressed.
Capacity Right rotation: To drill and to drive in screws, press the ro-
tational direction switch (10) through to the left stop.
80−100 %
Left Rotation: To loosen and unscrew screws and nuts,
60−80 %
press the rotational direction switch (10) through to the
40−60 %
right stop.
20−40 %
Preselecting torque (applies to screwdriving mode)
5−20 %
The torque presetting ring (3) can be used to pre-select the
0−5 %
required torque in 20 stages. Once the set torque has been
reached, the application tool will be stopped.
Setting the Operating Mode
Drilling
1 609 92A 583 | (13.12.2019)
English | 17