Operation; Maintenance - JetAir IX/A/60 Montage- Und Gebrauchsanweisung

Operation

The hood is fitted with a control panel with aspiration speed
selection control and a light switch to control cooking area
lights.
Use the high suction speed in cases of concentrated kitchen
vapours. It is recommended that the cooker hood suction is
switched on for 5 minutes prior to cooking and to leave in
operation during cooking and for another 15 minutes
approximately after terminating cooking.
Functioning - Model with display
The electronic controls on your ducting cooker hood
have multiple functions-features:
- Motor on-off function
The motor is turned on and off by pressing pushbutton nr. 1.
- Nr. 3 speeds
To select the required speed use pushbuttons nr. 2 and nr. 3.
The speed setting is given on the display provided for this
purpose.
- Timer function
This function permits you to program your cooker hood so that
the motor and lights turn off automatically 15 minutes after you
have activated this function. To program press pushbutton nr.
4. At the bottom on the right of the display a point will flash
indicating that the timer function is activated.
- Lights on-off function
To turn the lights on and off press pushbutton nr. 5
- Specific features
The electronic controls provided on your ducting cooker hood
have advanced features to facilitate maintenance and correct
utilization.
- Prompt - clean metal filters
After every 30 hours of use a microprocessor, heart of the
system, prompts the user that it is time to clean the metal
grease filters to guarantee better ducting performance and to
improve hygiene. This prompt is indicated by the letter "A"
which flashes on the display.
To delete this prompt, once the filters have been cleaned and
with the cooker hood off (not powered), maintain pushbutton
2 pressed for more than 5 seconds. When you press this
pushbutton the letter "A" will come up on the display and then
disappear after 5 seconds. The microprocessor zeros the
number of hours and starts a new count from zero until
reaching 30 hours prompting this maintenance procedure.
- Prompt - replace active carbon filters (if mounted)
If your cooker hood utilizes the re-circulation air filtering
system and therefore is fitted out with active carbon filters for
purifying the vapors extracted, it is necessary that you
program the microprocessor for this extraction system. To do
this, always with the cooker hood off (not powered), maintain
pushbutton nr. 4 pressed for 5 seconds. The symbol " –" will
come up on the display (this indicates the cooker hood is not
provided with a carbon filter) and after 5 seconds this symbol
changes to "C" (now indicating the cooker hood is provided
with a carbon filter). After every 120 hours of use the
microprocessor will prompt the user to replace the carbon
filter. This prompt is indicated by the letter "C" which flashes
on the display. This is to guarantee better filtering
performance and to improve hygiene.
To delete this prompt, once the filters have been replaced and
with the cooker hood off (not powered), maintain pushbutton
3 pressed for more than 5 seconds. When you press this
pushbutton the letter "C" will come up on the display and then
disappear after 5 seconds. The microprocessor zeros the
number of hours and starts a new count from zero until
reaching 120 hours prompting this maintenance procedure.

Maintenance

ATTENTION! Before performing any maintenance operation,
isolate the hood from the electrical supply by switching off at
the connector and removing the connector fuse.
Or if the appliance has been connected through a plug and
socket, then the plug must be removed from the socket.
Cleaning
The cooker hood should be cleaned regularly (at least with the
same frequency with which you carry out maintenance of the
fat filters) internally and externally. Clean using the cloth
dampened with neutral liquid detergent. Do not use abrasive
products. DO NOT USE ALCOHOL!
WARNING: Failure to carry out the basic cleaning
recommendations of the cooker hood and replacement of the
filters may cause fire risks.
Therefore, we recommend observing these instructions.
The manufacturer declines all responsibility for any damage to
the motor or any fire damage linked to inappropriate
maintenance or failure to observe the above safety
recommendations.
16