Instructions in Other Languages French German Spanish For additional help, call Ellison within USA 800.253.2238 or outside USA 949.598.8822 or within UK 0871 222 2277 or outside UK +44 (0) 845 345 2277 within USA Fax 800.253.2240 or outside USA Fax 949.598.8835...
IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS Read all the instructions before using WARNING the appliance. Read and understand these instructions before using your Prestige Machine. When using this product, basic precautions should always be followed, including the following: To reduce the risk of personal injury, close supervision is necessary when a ...
(page 8). Machine Placement Place Prestige Pro on a smooth, level, non-skid surface at a height that is comfortable for the user when standing. No part of the machine should be allowed to hang over the edge of the work surface.
Operating Instructions Pressure Right Side Plate Material Cutting Pad Back Front Left Side Figure A Figure B Using Standard SureCut and ClearCrop Dies (Large, Small and Tiny) ™ ™ 1. Raise the handle all the way up. 2. Place material to be cut against the rubber side of the die and place rubber side down on the Cutting Pad.
Pressure Plate Material Back Front Cutting Pad Figure C Figure D Figure E Using Extra Large (XL), Extra Large-Long (XL-L) or Double Cut ™ ™ (DC) SureCut and ClearCrop Dies An Extra Large (XL) or Double Cut (DC) Die is twice as long as a Tiny, Small or Large Die and requires two cuts.
With some XL or DC dies, and with any oversized dies (XL-L), it is helpful to cut an extra time in the middle of the die. Prestige Pro can be used to cut anything scissors can cut. See Materials Guide on pages 13 and 14 for suggestions.
With some XL, XL-L or DC dies, it is helpful to cut an extra time in the middle of the die. Use Prestige Pro to cut a variety of different materials. See Materials Guide on pages 13 and 14 for suggestions.
Figure H Recognizing a Worn Cutting Pad Prestige Pro requires very little maintenance. After considerable use (usually four to six months), the Cutting Pad (Figures H and I) will become worn. If the machine is not cutting effectively, perform a test cut with four pieces of construction paper, using the Test Die included in the Tool Kit.
Turning Over or Replacing the Cutting Pad Prestige Pro should cut six to eight layers of construction paper with one pull of the handle, without using scissors. Turning the Cutting Pad Over Please note that these instructions apply to both the PR Standard Cutting Pad and the CPR Premium Cutting Pad.
Return Your Machine for a Complete Renovation After many years of use, would you like your Prestige Pro to cut like new? If so, it's time for a tune-up. For price information sheet and return shipping...
7. Die rubber worn, missing or loose. Use yellow woodworking glue to attach loose rubber to the dies. If the rubber is worn or missing, call Ellison for re-rubbering instructions. 8. Rubber does not eject all parts of the cut material.
Materials Guide As a general rule, Prestige Pro will cut anything that scissors will cut. However, the machine bearings will last longer if the machine is not overloaded. The number of pieces of material that it will cut depends on the thickness of the material to be cut and the size and intricacy of the die design.
Warranties Prestige Pro Limited Lifetime Warranty What Does This Warranty Cover? This warranty covers any manufacturing defects in your Ellison Prestige Pro Die-cutting Machine (the “Product”). How Long Does The Warranty Last? This Product comes with a lifetime warranty. You should retain your receipt as proof of purchase, which may be required in connection with obtaining warranty service.
Seite 15
A Return Authorization (RA), along with shipping information, will be issued. Following a determination by Ellison that a fault covered by this warranty may have occurred, Ellison will: (a) ship you replacement parts or (b) ship you a replacement Product. Product not covered by this warranty will be returned at your expense.
à la fois pouvant provenir d’une grande variété de matériaux (cf. Guide des matériaux, p. 13 et 14). Le Prestige Pro fait pression sur les matrices à bande d’acier qui coupent le matériau. Les bords aiguisés de la matrice sont entourés de caoutchouc pour protéger les doigts et éjecter le matériau découpé.
Seite 18
(XL-L), il est utile de couper une autre fois au milieu de la matrice. Le Prestige Pro peut découper tout ce qui peut l’être avec des ciseaux. Consulter le Guide des matériaux (p. 13 et 14) pour y découvrir des suggestions.
Seite 19
Retourner ou remplacer le tapis de découpe Le Prestige Pro doit être en mesure de couper entre six et huit couches de papier de bricolage d’un seul coup de manette, sans avoir recours à l’utilisation de ciseaux.
Seite 20
Retourner l’appareil pour une remise en état complète Après plusieurs années d’utilisation, que diriez-vous si le Prestige Pro coupait comme au premier jour ? Une mise au point s’impose. Pour obtenir les tarifs et les instructions concernant l’expédition des retours, appeler Ellison au 800.253.2238...
Seite 21
Guide des matériaux En règle générale, le Prestige Pro coupe tout ce qui peut l’être avec des ciseaux. Cependant, les rouleaux de l’appareil dureront plus longtemps si l’appareil n’est pas surchargé. Le nombre de morceaux qui peuvent être coupés dépend de l’épaisseur du matériau, ainsi que de la taille et de la complexité...
(siehe Seite 8). Aufstellen des Geräts Stellen Sie das Prestige Pro Gerät auf eine glatte, ebene und rutschfeste Arbeitsfläche in einer Höhe, die ein bequemes Arbeiten im Stehen erlaubt. Achten Sie darauf, dass keine Geräteteile über die Kante der Arbeitsfläche hinausragen.
Bei machen XL- oder DC-Stanzeisen und bei allen übergroßen Stanzeisen (XL-L) ist ein weiterer Stanzvorgang in der Mitte des Stanzeisens hilfreich. Prestige Pro kann zum Stanzen aller Materialien verwendet werden, die auch mit einer Schere geschnitten werden können. Vorschläge sind unter „Verwendbare Materialien“...
Seite 24
Anzeichen für eine abgenutzte Stanzplatte Das Prestige Pro ist sehr einfach zu warten. Nach vielen Einsätzen (in der Regel nach vier bis sechs Monaten) ist die Stanzplatte (Abb. H und I) abgenutzt. Wenn die Maschine nicht mehr richtig schneidet, führen Sie eine Teststanzung mit vier Lagen Bastelpapier durch und verwenden dazu das Teststanzeisen im Werkzeugsatz.
Seite 25
Geben Sie die Maschine zur Generalüberholung an den Hersteller zurück Möchten Sie, dass Ihr Prestige Pro auch nach Jahren noch wie neu stanzt? Dann ist es Zeit für eine Generalüberholung. Preisinformationen und eine Anleitung zum Einsenden des Geräts erhalten Sie telefonisch bei Ellison.
8. Der Gummi wirft nicht alle Teile des ausgestanzten Materials aus. Entfernen Sie überschüssiges Material nach jedem Einsatz mit dem Stanzpick. Wenn der Gummi abgenutzt ist oder fehlt, fordern Sie bei Ellison eine Anleitung zum Anbringen einer neuen Gummibeschichtung an.
(consulte la Guía de materiales, páginas 13 y 14). La Prestige Pro aplica presión a los troqueles con una regla de acero que corta el material. La afilada hoja cortante de los troqueles está...
Seite 28
Con algunos troqueles XL, XL-L o DC, es útil cortar una vez más en el medio del troquel. Use la Prestige Pro para cortar una gran variedad de materiales diferentes. Para obtener sugerencias, consulte la Guía de materiales en las páginas 13 y 14.
Seite 29
Inversión o cambio de la almohadilla de corte La Prestige Pro debe cortar de seis a ocho capas de cartulina al tirar una vez de la manija, sin utilizar tijeras. Inversión de la almohadilla de corte Tenga presente que estas instrucciones se aplican tanto a la almohadilla de corte estándar PR como a la almohadilla de corte Premium CPR.
Seite 30
Si es así, es momento de realizar una puesta a punto. Para conseguir una hoja con información sobre precios e instrucciones de devolución, llame a Ellison dentro de EE. UU. al 800.253.2238 o desde fuera de EE. UU. al 949.598.8822.
Seite 31
8. La goma no expulsa todas las partes del material de corte. Use la púa del troquel para extraer el exceso de material después de cada uso. Si la goma está gastada o no hay goma, llame a Ellison y solicite instrucciones sobre cómo volver a colocarla.