Instruction Manual; Safety Warnings - Makita DPT353 Betriebsanleitung

ENGLISH (Original instructions)
SPECIFICATIONS
Model:
Pin nail size
Pin nail magazine capacity
Dimensions without hook (L x W x H)
Rated voltage
Battery cartridge
Net weight
• Due to our continuing program of research and development, the specifications herein are subject to change
without notice.
• Specifications and battery cartridge may differ from country to country.
• Weight, with battery cartridge, according to EPTA-Procedure 01/2003
Intended use
The tool is intended for pressing pin nails into construc-
tion materials such as timbers.
Noise
The typical A-weighted noise level determined accord-
ing to EN60745:
Sound pressure level (L
Uncertainty (K) : 3 dB(A)
The noise level under working may exceed 80 dB (A).
WARNING:
Wear ear protection.
Vibration
The vibration total value determined according to EN60745:
Vibration emission (a ) : 2.5 m/s
h
Uncertainty (K) : 1.5 m/s
NOTE: The declared vibration emission value has been
measured in accordance with the standard test method
and may be used for comparing one tool with another.
NOTE: The declared vibration emission value may
also be used in a preliminary assessment of exposure.
WARNING:
The vibration emission during actual
use of the power tool can differ from the declared emission
value depending on the ways in which the tool is used.
WARNING:
Be sure to identify safety measures
to protect the operator that are based on an estima-
tion of exposure in the actual conditions of use (taking
account of all parts of the operating cycle such as
the times when the tool is switched off and when it is
running idle in addition to the trigger time).
EC Declaration of Conformity
For European countries only
The EC declaration of conformity is included as Annex A
to this instruction manual.
) : 76 dB(A)
pA
2
or less
2
ø0.6 mm x 15, 18, 25, 30, 35 mm
257 mm x 79 mm x 226 mm
BL1815, BL1815N, BL1820,
BL1820B
2.0 kg

SAFETY WARNINGS

General power tool safety warnings
WARNING:
Read all safety warnings, instruc-
tions, illustrations and specifications provided
with this power tool. Failure to follow all instructions
listed below may result in electric shock, fire and/or
serious injury.
Save all warnings and instruc-
tions for future reference.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.
Cordless nailer safety warnings
Always assume that the tool contains fasten-
1.
ers. Careless handling of the nailer can result in
unexpected firing of fasteners and personal injury.
Do not point the tool towards yourself or any-
2.
one nearby. Unexpected triggering will discharge
the fastener causing an injury.
Do not actuate the tool unless the tool is
3.
placed firmly against the workpiece. If the tool
is not in contact with the workpiece, the fastener
may be deflected away from your target.
4. Disconnect the tool from the power source
when the fastener jams in the tool. While
removing a jammed fastener, the nailer may be
accidentally activated if it is plugged in.
5. Use caution while removing a jammed fas-
tener. The mechanism may be under compression
and the fastener may be forcefully discharged
while attempting to free a jammed condition.
6. Do not use this nailer for fastening electrical
cables. It is not designed for electric cable installa-
tion and may damage the insulation of electric cables
thereby causing electric shock or fire hazards.
5 ENGLISH
DPT353
100 pcs.
D.C. 18 V
BL1830, BL1830B, BL1840,
BL1840B, BL1850, BL1850B,
BL1860B
2.2 kg