Hob Cookware Advice - Hoover HH74DBXP Gebrauchs- Und Installationsanweisungen

"Installation must conform to the standards & directives."
Manufacturer declines all responsibility for any damage that might
be caused by unsuitable or unreasonable use.
WARNING: Manufacturer cannot be held responsible for any incident or
its consequences that may arise during the use of an appliance not linked
to the earth, or linked to an earth whose continuity is defective. Before any
electrical operation, please check the supply tension shown on the
electricity meter, the adjustment of the circuit- breaker, the continuity of the
connection to earth to the installation and that the fuse is suitable.
The electrical connection to the installation should be made according to
the rated power of the Appliance; this should be made via an Omni pole
cut-out switch.
If the appliance has a socket outlet, it must be installed so that the socket
outlet is accessible.
The yellow/green wire of the power supply cable must be connected to the
earth of both power supply and appliance terminals.
For any questions regarding power supply cord refer to After Sales
Service or a qualified technician.
If the hob is fitted with power supply cord, this shall be connected only to a
power supply of 220-240 V between phase and neutral.
It is however possible to connect the hob to:
Three Phase 220-240 V3
Three Phase 380-415 V2N
To proceed to the new connection, please follow below instructions:
Before making the connection, make sure that the installation is protected
by a suitable fuse, and that it is fitted with wires of a large enough section to
supply the appliance normally.
Turn over the hob, glass side against the working top, taking care to protect
the glass.
Open the cover in the following sequence:
1 2
- unscrew the cable clamp "1";
- find the two tabs located on the sides;
- put the blade of a flat screw-driver in front of each tab "2" e
"3", push in and press;
- remove the cover.
To release the power supply cord:
- Remove the screws retaining the terminal block which
the shunt bars and the conductors of the supply cord;
- Pull out the supply cord.
Operations to be carried out to make a new connection:
- Choose the power supply cable in accordance with the recommendations in
the table;
- Pass the power supply cable into the clamp;
- Strip the end of each conductor of the supply cord on a 10 mm length, by
taking in account the requested length of the cord for the connection to the
terminal block;
- According to the installation and with the help of shunt bars which you should
have recovered in the first operation, fix the conductor as shown on the chart;
- Fix the cover;
- Screw the cable clamp.
Note: make sure the terminal board screws are tight.
Operations to be carried out to make a new connection:
- Choose the power supply cable in accordance with
the recommendations in the table;
- Pass the power supply cable into the clamp;
- Strip the end of each conductor of the supply cord
on a 10 mm length, by taking in account the
requested length of the cord for the connection to the
terminal block;
- According to the installation and with the help of
shunt bars which you should have recovered in the
first operation, fix the conductor as shown on the
chart;
- Fix the cover;
- Screw the cable clamp.
3
contains
SHUNT
06 GB
ATTENTION:
If it should be necessary to replace the power supply cord, connect the
wire in accordance with following colors/codes:
Connection to the terminals on the terminal block
LAY OUT
MONOPHASE or TWO PHASES 220-240 V
Cable
3x2,5 mm
HO5V2V2F
THREE PHASES 220-240 V
Cable
4x1,5 mm
HO5V2V2F
THREE PHASES 380-415 V
Cable
4x1,5 mm
HO5V2V2F
380-415V 2N ~
PE L1 L2
220-240V ~
PE
L
L1 / L2 / L3 = Phase

5. HOB COOKWARE ADVICE

Using good quality cookware is critical for setting
the best performance from your hob.
• Always use good quality cookware with perfectly flat and thick
bases : using this type of cookware will prevent hot spots that cause
food to stick. Thick metal pots and pans will provide an even
distribution of heat.
• Ensure that the base of the pot or pan is dry :
pans with liquid or using one that has been stored in the
ensure that the base of the pan is completely dry before placing it on
the hob. This will help to avoid staining the
• Use pans whose diameter is wide enough to completely cover
the surface unit : the size of the pan should be no
than the heating area. If it is slightly wider the energy will be used at its
maximum efficiency.
THE CHOICE OF COOKWARE - The following information will help
you to choose cookware which will give good performance.
Stainless Steel : highly recommended. Especially good with a
sandwich clad base. The sandwich base combines the benefits of
stainless steel (appearance, durability and stability) with the
advantages of aluminium or copper (heat conduction, even heat
distribution).
Aluminium : heavy weight recommended. Good conductivity.
Aluminium residues sometimes appear as scratches on the hob, but
can be removed if cleaned immediately.
Because of its low melting point, thin aluminium should not be used.
Cast Iron : usable, but not recommended. Poor performance. May
scratch the surface.
( )
LAY OUT
"1-3" "2-4"
~
2 2
3x4 mm
3~
2 2
4x1,5 mm
2N~
2 2
4x1,5 mm
220-240V 3 ~
L3 L2
PE L1
220-240V 2 ~
L2
PE L1
N = Neutral PE = Earth
when filling
refrigerator,
hob.
s m a l l e r