Further Information - Fisher & Paykel Active Smart Ice & Water Schnellstartanleitung

5
Installation guidelines – Ice & Water models contd.
To flush the water filter and check for leaks, aim the end of the tubing
9
into a bucket, turn isolating tap on and run at least 10 L of water through.
10 Locate desired position for water filter noting the following points:
Fit the water filter in a vertical orientation (water filter head at the top).
■ ■
Ensure the filter is in a convenient location to access every 6 months
■ ■
for replacement.
A minimum clearance of 64 mm from the bottom of the filter cartridge
■ ■
is required to perform cartridge removal.
Do not screw water filter to refrigerator.
■ ■
11 Attach double sided foam to the back of the water filter head and attach
filter to the desired position.
Run the 6 mm tubing to back of the fridge ensuring there is enough tubing to pull out the refrigerator
12
for service.
Connect tubing into the water (solenoid) valve located on the right hand side of the unit (compressor)
13
compartment as shown in Fig.2. Beware of hot pipes.
Pull gently on tubing to ensure it is locked in.
14
The completed installation should look like Fig.3.
15
3 1 2
Turn isolating tap on and check that all connections are dry and free of drips.
16
17 Coil water line tubing behind the fridge. Push your refrigerator into place being careful not to kink or
squash the water line running into the water (solenoid) valve.
The first time you dispense water, there will be a delay while the water tank fills up.
18
Run a further 3 L through the system to ensure the tank is flushed out.
19
You are now ready to enjoy chilled water and ice dispensing from your Active Smart™ refrigerator.
20
7
Using the display – Ice & Water models
The temperature of your refrigerator and freezer
When the refrigerator is first turned on, it will take approximately 2 to 3 hours to cool.
■ ■
The refrigerator is pre-set to its recommended (middle) setting.
■ ■
To adjust the temperature of a compartment, use the
■ ■
use the button to select the compartment you want to change.
Adjust using the button to make the compartment warmer or the
■ ■
colder.
The temperature setting will be indicated on the icon below.
■ ■
Using your water dispenser
First use
After installation, allow approximately a one minute delay while the dispensing pad is pushed until
■ ■
water is dispensed. This will allow the tank to fill completely.
After you fill the tank, dispense and discard 3 L to flush the tank out.
■ ■
Using your ice maker
Ice maker
First use
When you first turn your refrigerator on, the ice maker will be off.
■ ■
To turn on use the button to scroll to the
■ ■
Use the or buttons to turn the ice maker on or off.
If the bin is full of ice, or inserted incorrectly, the ice maker will not operate. If all bins are removed the
■ ■
ice maker will not operate.
Discard ice cubes made in the first 24 hours of operation.
■ ■
We recommend that you turn the ice maker off if:
■ ■
– The water supply is off for several hours,
– The ice storage bin is to be removed for a period of time,
– You are going on holiday/vacation.
Fast Freeze
This feature drops the freezer to its coldest temperature for 12 hours and then returns to normal.
To activate, use the button until the Fast Freeze icon (
■ ■
screen. Then use the or buttons until the snowflakes ( ) are displayed on the Fast Freeze screen.
The animating snowflakes indicate that Fast Freeze has been activated.
To deactivate manually, use the button to scroll to the Fast Freeze icon (
■ ■
use the and until there are no snowflakes ( ) present on the screen.
Fig.2 Waterline connection
to refrigerator
Fig.3 Connection to water supply
button to scroll to the
button to make the compartment
screen.
) is showing on the
) on the screen. Then
6
Using the display – Non Ice & Water models
Temperature control
When the refrigerator is first turned on, it will take 2 – 3 hours to cool.
■ ■
The refrigerator is pre-set to its recommended (middle) setting.
■ ■
The two compartment temperatures are accurately and independently controlled and do not change
■ ■
with the temperature or humidity of the surroundings; whether summer or winter.
Control panel
to adjust temperatures (located at back of fresh food compartment)
Fresh food and freezer
compartment indicator
Compartment
select button
The fresh food compartment light on the refrigerator diagram will be showing. The temperature
■ ■
indicator (the thermometer) will show the temperature setting for this compartment as a series of lights.
The temperature may be altered by pressing the
■ ■
One press on either of these buttons will produce a dimmer light which indicates a small change in
■ ■
temperature.
Pressing either button twice gives a brighter light and indicates a greater change in temperature.
■ ■
To adjust the freezer temperature press the
■ ■
compartment indicator and use the
Note: successively pressing the
to the fresh food compartment will be accompanied by a longer beep.
When the door is reopened the control panel will return automatically to the fresh food
■ ■
compartment setting.
8 8
Using the display – Ice & Water models contd.
Bottle Chill
Bottle Chill cools drinks more rapidly, it will remind you to remove your bottle by sounding an alarm.
screen,
The user alarm will continue to sound until any key on the panel is pressed.
To activate, use button until the bottle chill icon (
■ ■
screen. Then use the or
displayed on the Bottle Chill screen.
Then use the button to select 10, 15, 20, 25 or 30 minutes as displayed on the Bottle Chill screen.
■ ■
After several seconds, the snowflakes will then animate as the timer counts down.
An alarm will sound after the amount of time selected has elapsed.
■ ■
Press any button on the display to silence the alarm. Remember to remove the beverage from the freezer.
■ ■
To deactivate Bottle Chill manually, use the
■ ■
on the
screen and the snowflakes ( ) are no longer visible.

Further information

Before you call for service or assistance...
Check the things you can do yourself. Refer to the installation instructions, your User Guide –
in particular the troubleshooting section and check that:
your product is correctly installed
1
you are familiar with its normal operation.
2
If after checking these points you still need assistance or parts, refer to www.fisherpaykel.eu for regional
service providers.
Increase temperature button
Decrease temperature button
Temperature indicator
(thermometer)
or buttons.
button until the light flashes on the freezer
or buttons in the same way.
button will automatically select between the compartments, a return
) is showing on the
buttons until the snowflakes ( ) and the minute timer (
button to scroll to the bottle chill icon (
screen, then use the and buttons until no minutes are shown on the
) are
)
821257 08.11 EU