Introduction; Prevention Against Electric Shocks - INE Skyline 1500 Bedienungsanleitung

INE S.p.A. Via Facca, 10 - 35013 Cittadella - PADOVA - ITALIA Tel. 049/9481111 - Fax 049/9400249 - ine@ine.it - www.ine.it

Introduction

SKYLINE 1500 is an innovative current generator for
rod welding (MMA - SMAW), designed for even the
most discerning professional, while being extremely
simple to use for the less expert welders to guarantee
results that are always perfect.
The innovative technology that has been adopted, the
scrupulous construction care and the use of cutting
edge materials and components have helped reduce
the weight, the volume and the energy intake,
increasing its reliability, performance and the welding
features.
Besides excellent results with standard electrodes
(rutile, basic, stainless steel, aluminium, etc.) the
generator also allows using cellulosic electrodes with
equally excellent results. It can be used for TIG dc
(GTAW) lift welding.
Furthermore, with the innovative intake power control
function it is ideal for using with any sort of generating
sets, even low voltage ones, exploiting all its available
energy.
Furthermore, these main characteristics are supported
by the traditional sturdy and reliable construction of INE
welding machines.
SKYLINE 1500 welding machines are constructed
according to the following standards EN 60974:
•
as far as operators health prevention against electric
shocks is concerned.
•
as far as electromagnetic compatibility is concerned
(noise disturbing other
operating in the vicinity).
INE declines any liability should the welding machine
be used incorrectly (ex.: to defrost pipes, to charge
batteries, etc.) or modified by the customer or third
parties without any
manufacturer.
INE generators have been designed for professional
use and must be used exclusively by adequately
trained persons.

Prevention against electric shocks

The machine must be installed by authorised persons
with specific technical and professional know-how,
conforming to the laws in force in the country where it is
installed.
Before connecting the power source to the mains,
always check that:
•
the voltage received falls within ±15% allowance of
the nominal value displayed on the machine plate;
•
the mains input is properly grounded (as provided in
the relevant legislation) and the yellow/green wire of
the welding machine is connected to the ground;
•
the mains supply is equipped with a grounded
neutral conductor;
electrical appliances
written approval by
•
the power source is in a dry and ventilated place.
When using the welding machine, make sure that the
following precautionary measures are taken in the
workplace:
•
ensure that no metallic body may accidentally get
into contact with the power cables;
•
do not carry out any welding operation in damp or
wet areas;
•
ground any metallic parts falling within the operator's
reach;
•
keep all flammable materials away from the working·
area;
•
ensure that the gas cylinder is secured so as not to
hit or be hit by or anyway come into contact with the
welding circuit;
•
connect the work return lead of the welding circuit to
a place as close as possible to the welding area in
order to minimise the current path and the relevant
risks;
•
make sure that welding torches and cables are in
perfect condition.
Furthermore, the operator should stick to the following
behavioural rules:
•
do not connect welding machines in series or
parallel;
•
in the case two or more welders should operate on
electrically connected parts, it is suggested that they
work at a suitable distance from each other and that
none of them touches two torches or electrode
holders at the same time;
•
do not place the torch or electrode holder on metallic
surfaces: this might be a condition for the machine to
be started accidentally;
•
the
always wear insulating garments.
In the case the power source should be introduced into
areas characterised by a high risk of electric shocks, it
is recommended that the connection to the mains be
protected by a highly-sensitive differential circuit
breaker (releasing current: 30 mA, operating time: 30
ms).
Such areas are:
A) places offering limited freedom of movement and
preventing the operator from standing while working;
B) places surrounded by conductive surfaces that may
accidentally come into contact with the welding circuit;
C) wet, damp and hot places.
Page 10