Makita DCL142 Bedienungsanleitung Seite 10

NOTE: Depending on the conditions of use and the
ambient temperature, the indication may differ slightly
from the actual capacity.
Battery power lamp
► Fig.6: 1. OFF button 2. HIGH/LOW button
3. Battery power lamp
• When the remaining battery capacity gets low, the
battery power lamp blinks.
• When the remaining battery capacity gets much lower,
the tool stops during operation and the battery power
lamp lights up for about ten seconds. At this time,
remove the battery cartridge from the tool and charge it .
NOTE:
• The time at which the battery power lamp start
blinking or lighting up depends on the temperature
at work place and the battery cartridge conditions.
ASSEMBLY
CAUTION:
• Always be sure that the tool is switched off and
the battery cartridge is removed before carrying
out any work on the tool.
Disposing of Dust
CAUTION:
• Empty the cleaner before it becomes too full, or
the suction force weakens.
• Be sure to empty out the dust inside the cleaner
itself. Failure to do so may cause the sponge
filter to be clogged or the motor to be damaged.
• Never throw away the dust stopper because it
should be used whenever either the dust bag or
the paper pack is used.
► Fig.7: 1. Front cover 2. Button
1. Push the button to open the front cover. Opening it until
a click is heard allows a positive stop at that position.
► Fig.8: 1. Front cover 2. Front cover joint
NOTE:
• The cleaner is constructed in such a way that
the front cover comes off when trying to force
the front cover open at the angle of more than
90°. If the front cover comes off, insert it into the
front cover joint in place.
CAUTION:
• When closing the front cover, be careful not to
pinch your fingers.
► Fig.9: 1. Dust stopper
2. Pull out both the orange-colored dust stopper and
dust bag together at the same time.
► Fig.10: 1. Dust stopper
► Fig.11
3. Remove the dust stopper and empty the cleaner.
Dust bag and paper pack
Install either dust bag or paper pack before using cleaner.
Use the dust stopper when installing either dust bag or
paper pack.
The dust bag can be used repeatedly by cleaning it out.
Paper pack is a throw-away type. Throw away the entire
paper pack without emptying when it has become full.
Installing dust bag
► Fig.12: 1. Upper side of dust stopper 2. Lower side
of dust stopper
Use the dust stopper when installing dust bag. Be
careful not to take the upper side for the lower side by
mistake because they are different each other.
► Fig.13: 1. Dust stopper 2. Groove 3. Dust bag
1. Insert the protrusion of the dust bag into the
groove in the dust stopper as shown in the figure.
► Fig.14: 1. Lower groove
2. There is no distinction between the upper and lower
sides of the dust bag. You may insert its protrusion
of any side into the lower groove of the dust stopper.
► Fig.15
3. Overlap the frame of dust stopper with that of the dust bag.
► Fig.16: 1. Cleaner cavity
4. Place the dust stopper and the dust bag together
into the cleaner cavity in the same direction of
arrow on the dust stopper. Insert them all the way
into the slots in the cleaner cavity.
► Fig.17
5. Place the entire cloth part of the dust bag inside
the tool itself.
► Fig.18: 1. Front cover
6. Close the front cover completely.
Installing the paper pack
► Fig.19
1. Unfold the entrance of the paper pack before
setting it on the dust stopper.
► Fig.20: 1. Upper side of dust stopper 2. Lower side
of dust stopper
Use the dust stopper also when installing paper pack.
Be careful not to take the upper side for the lower side
by mistake because they are different each other.
► Fig.21: 1. Dust stopper 2. Paper pack 3. Groove
2. Insert the protrusion of the paper pack into the
groove in the dust stopper as shown in the figure.
► Fig.22: 1. Lower groove
3. There is no distinction between the upper and lower
sides of the paper pack. You may insert its protrusion
of any side into the lower groove of the dust stopper.
► Fig.23
4. Overlap the frame of dust stopper with that of the
paper pack.
► Fig.24: 1. Cleaner cavity
5. Place the dust stopper and the paper pack
together into the cleaner cavity in the same direc-
tion of arrow on the dust stopper. Insert them all
the way into the slots in the cleaner cavity.
10 ENGLISH