Cleaning And Maintenance - KikkaBoo TWISTER Montageanleitung

Seite von 55

/ 55
Inhalt
Inhaltsverzeichnis
Lesezeichen

Inhaltsverzeichnis

Verfügbare Sprachen

1. E nsure the seat is not in a reclined position (the indicator should be in position 1) and is ready to install in forward position (Group 1) as shown in fig. 6.1.

Pull the lever (G) forward and adjust the angle of recline to position 1 without releasing the lever. If it is necessary swivel the seat 180º to place the seat in the

direction of travel (fig. 6.1.A). Release the lever when the seat is in the desired position.

2. By turning the Isoclick Fix arms, extract both arms (N) located in the base of the seat (fig. 6.2).

3. Place the child safety seat in the back seat of the vehicle facing in the direction of travel (fig. 6.3).

4. Hold the safety seat with both hands and insert the two Isoclick Fix arms (N) firmly into the vehicle´s isofix anchoring points until they fasten with a click

on both sides. The red button will change to green on both sides (fig.6.3).

5. Pass the vehicle seat belt through the slot on the back of the safety seat (M) until it appears at the exit (fig. 6.4). Buckle the vehicle seat belt until you hear

a click (fig. 6.5).

6. T ake up the slack by pulling the abdominal section of the belt until it is as tight-fitting as possible (fig 6.6).

7. E nsure the straps are not twisted at any point.

PLACING THE CHILD IN THE SEAT GROUP 1

To seat the child correctly follow the steps described in chapter 4.

REMOVING THE HARNESS AND SAFETY BUCKLE

Removing the 5 point harness and the safety buckle

1. Loosen the harness straps by pulling them gently while pressing the harness adjustment button (E) (fig.8.1)

2. L oosen the harness straps from the back of the seat, freeing them from the harness connector (I). Repeat the operation with the shoulder straps connector

(O) (fig. 8.2 and 8.3).

3. Pull the harness straps from the front to free them from the seat back (fig.8.4).

4. Take off the safety buckle (D), passing the retention plate through the seat base slots.

Removing the fabric cover

1. Take off the headrest fabric cover (fig.8.5).

2. T ake off the seat cover unbuttoning the brackets that secure the cover to the plastic base. Pull the shoulder straps (B) through the base cover eyelets

(fig.8.6).

3. T ake off the fabric cover from the car seat.

INSTALING THE CHILD SEAT GROUP 2

Before installing the seat for Group 2, the seat harnesses (B), harness protectors (C) and buckle (D) must be removed. Please, for this, follow

chapter 8.1.

1. E nsure the seat is not in a reclined position (the indicator should be in position 1) and is ready to install in forward position (Group 1) as shown in fig. 6.1.

Pull the lever (G) forward and adjust the angle of recline to position 1 without releasing the lever. If it is necessary swivel the seat 180º to place the seat in the

direction of travel (fig. 6.1.A). Release the lever when the seat is in the desired position (fig. 6.1)

2. Place the child safety seat in the back seat of the vehicle facing in the direction of travel (fig. 6.3).

10.

PLACING THE CHILD IN THE SEAT GROUP 2

1. According to the child's height the headrest can be adjusted up or down. Place your hand on the headrest height regulator and pull while pulling the seat

down with the other hand so it does not move (9.1).

2. Place the child safety seat in the back seat of the vehicle facing in the direction of travel.

3. Pass the vehicle seat belt through the slot on the back of the safety seat (M) until it appears at the exit as you see in the illustrations 9.2 and 9.3.

4. Place the child in the seat.

5. Pass the vehicle seat belt across the child's body and insert the belt in the other side safety seat slot (M) until it appears at the exit and buckle the vehicle

seat belt until you hear a click (fig. 9.4).

6. T ake up the slack by pulling the abdominal section of the belt until it is as tight-fitting as possible. Ensure that the belt is tighten.

11.