Operation; Correct Posture; Maintenance - Makita DUR365U Bedienungsanleitung

OPERATION

Correct handling of tool
WARNING:
• Be extremely careful to maintain control of
the tool at all times. Do not allow the tool to
be deflected toward you or anyone in the
work vicinity. Failure to keep control of the tool
could result in serious injury to the bystander
and the operator.

Correct posture

WARNING:
• Always hold the both grips firmly and posi-
tion the tool on your right-hand side so that
the shaft of the left handle is always in front
of your body. Correct positioning of the tool
allows for maximum control and will reduce
the risk of serious personal injury caused by
kickback.
► Fig.24
Fit the shoulder harness and hang the tool firmly on
your right side so that the shaft of the left handle is
always ahead of you.
Attachment of shoulder harness
► Fig.25: 1. Buckle 2. Hook
Wear the shoulder harness on your left shoulder. Make
sure that the buckle cannot be taken off with pulling it
off. Hang the tool as shown.
► Fig.26: 1. Buckle
The buckle is provided with a means of quick release.
Simply squeeze the sides of the buckle to release the
tool.
Adjustment of the hanger position
and shoulder harness
To change the hanger position, loosen the fixing screw
on the hanger with the supplied wrench and then move
the hanger and the cushion. The cushion can be moved
easily by twisting it.

MAINTENANCE

WARNING:
Always be sure that the tool is switched
•
off and battery cartridge is removed before
attempting to perform inspection or main-
tenance on the tool. Failure to switch off and
remove the battery cartridge may result in seri-
ous personal injury from accidental start-up.
NOTICE:
Never use gasoline, benzine, thinner, alcohol or
the like. Discoloration, deformation or cracks may
result.
Replacing the nylon cord
WARNING:
specified in "SPECIFICATIONS" only. Never use
heavier line, metal wire, rope or the like. Use rec-
ommended nylon cord only, otherwise it may cause
damage to the tool and result in serious personal
injury.
WARNING:
nylon cutting head is secured to the housing
properly as described below. Failure to properly
secure the cover may cause the nylon cutting head to
fly apart resulting in serious personal injury.
For 95-M10L
1. Press on the housing latches inward to lift off the
cover, then remove the spool.
► Fig.27: 1. Latch 2. Cover
2. Prepare approximately 3 m (9 ft) of new nylon
cord. Fold the new nylon cord with one end become
approximately 80 mm (3-1/8") longer than the other
end. Then hook the new nylon cord into the notch in the
center of the spool.
Wind both ends firmly around the spool in the direction
of the head rotation (left-hand direction indicated by LH
on the side of the spool).
► Fig.28: 1. Spool
3. Wind all but about 100 mm (3 - 15/16") of the
cords, leaving the ends temporarily hooked through a
notch on the side of the spool.
► Fig.29
4. Mount the spool in the housing so that the grooves
and protrusions on the spool match up with those in the
housing. Keep the side with letters on the spool visible
on the top. Now, unhook the ends of the cord from their
temporary position and feed the cords through the
eyelets to come out of the housing.
► Fig.30: 1. Spool 2. Housing 3. Eyelet
5. Align the protrusion on the underside of the cover
with the slots of the eyelets. Then push the cover firmly
onto the housing to secure it.
► Fig.31
For B&F ECO4L
► Fig.32
Take off cover from housing, pressing two latches which
are slotted section oppositely on side of housing.
► Fig.33: 1. 80-100 mm
Cut a nylon line in 3 m. Fold the cutting line in two
halves, leave one of half longer 80-100 mm than
another.
► Fig.34
Hook the middle of the new nylon cord to the notch
located at the center of the spool between the 2 chan-
nels provided for the nylon cord.
Wind both ends firmly around the spool in the direction
marked on the head for left hand direction indicated by
LH.
16 ENGLISH
Use nylon cord with diameter
Make sure that the cover of the